ML4861
RESET COMPARATOR
FUNCTIONAL DESCRIPTION
An additional comparator is provided to detect low V ,
IN
The ML4861 combines Pulse Frequency Modulation
(PFM) and synchronous rectification to create a boost
converter that is both highly efficient and simple to use. A
PFM regulator charges a single inductor for a fixed period
of time and then completely discharges before another
cycle begins, simplifying the design by eliminating the
need for conventional current limiting circuitry.
or any other error condition that is important to the user.
The inverting input of the comparator is internally
connected to V , while the non-inverting input is
REF
provided externally at the DETECT pin. The output of the
comparator is the RESET pin, which swings from V
to
OUT
GND when an error is detected.
Synchronous rectification is accomplished by replacing an
external Schottky diode with an on-chip PMOS device,
reducing switching losses and external component count.
DESIGN CONSIDERATIONS
INDUCTOR
REGULATOR OPERATION
Selecting the proper inductor for a specific application
usually involves a trade-off between efficiency and
A block diagram of the boost converter is shown in Figure
2. The circuit remains idle when V
is at or above the
OUT
maximum output current. Choosing too high a value will
keep the regulator from delivering the required output
current under worst case conditions. Choosing too low a
value causes efficiency to suffer. It is necessary to know
the maximum required output current and the input
voltage range to select the proper inductor value. The
maximum inductor value can be estimated using the
following formula:
desired output voltage, drawing 45µA from V , and 8µA
IN
from V
through the feedback resistors R1 and R2.
drops below the desired output level, the
OUT
When V
OUT
output of amplifier A1 goes high, signaling the regulator to
deliver charge to the output. Since the output of amplifier
A2 is normally high, the flip-flop captures the A1 set signal
and creates a pulse at the gate of the NMOS transistor Q1.
The NMOS transistor will charge the inductor L1 for 10µs,
resulting in a peak current given by:
V
2 × TON(MIN) × η
IN(MIN)
LMAX
=
(2)
2 × VOUT ×IOUT(MAX)
T
ON × V
10µs × V
IN
IN
IL(PEAK)
=
≈
(1)
L1
L1
where h is the efficiency, typically between 0.8 and 0.9.
Note that this is the value of inductance that just barely
delivers the required output current under worst case
conditions. A lower value may be required to cover
inductor tolerance, the effect of lower peak inductor
currents caused by resistive losses, and minimum dead
time between pulses.
For reliable operation, L1 should be chosen so that I
does not exceed 2A.
L(PEAK)
When the one-shot times out, the NMOS transistor
releases the V pin, allowing the inductor to fly-back and
L
momentarily charge the output through the body diode of
PMOS transistor Q2. But, as the voltage across the PMOS
transistor changes polarity, its gate will be driven low by
the current sense amplifier A2, causing Q2 to short out its
body diode. The inductor then discharges into the load
through Q2. The output of A2 also serves to reset the flip-
flop and one-shot in preparation for the next charging
cycle. A2 releases the gate of Q2 when its current falls to
Another method of determining the appropriate inductor
value is to make an estimate based on the typical
performance curves given in Figures 4 and 5. Figure 4
shows maximum output current as a function of input
voltage for several inductor values. These are typical
performance curves and leave no margin for inductance
and ON-time variations. To accommodate worst case
conditions, it is necessary to derate these curves by at
least 10% in addition to inductor tolerance.
zero. If V
is still low, the flip-flop will immediately
OUT
initiate another pulse. The output capacitor (C1) filters the
inductor current, limiting output voltage ripple. Inductor
current and one-shot waveforms are shown in Figure 3.
For example, a two cell to 5V application requires 80mA
of output current while using an inductor with 15%
tolerance. The output current should be derated by 25%
to 100mA to cover the combined inductor and ON-time
tolerances. Assuming that 2V is the end of life voltage of a
two cell input, Figure 4 shows that with a 2V input, the
ML4861-5 delivers 108mA with a 27µH inductor.
INDUCTOR
CURRENT
Q2
ON
Q2
ON
Q(ONE SHOT)
Q1 ON
Q1 ON
Q1 & Q2 OFF
Figure 3. PFM Inductor Current Waveforms and Timing.
5
MICRO-LINEAR [ MICRO LINEAR CORPORATION ]
