欢迎访问ic37.com |
会员登录 免费注册
发布采购

MIC2526-1BM 参数 Datasheet PDF下载

MIC2526-1BM图片预览
型号: MIC2526-1BM
PDF下载: 下载PDF文件 查看货源
内容描述: 双USB电源控制开关不推荐用于新设计 [Dual USB Power Control Switch Not Recommended for New Designs]
分类和应用: 电源电路开关电源管理电路光电二极管
文件页数/大小: 12 页 / 97 K
品牌: MICREL [ MICREL SEMICONDUCTOR ]
 浏览型号MIC2526-1BM的Datasheet PDF文件第2页浏览型号MIC2526-1BM的Datasheet PDF文件第3页浏览型号MIC2526-1BM的Datasheet PDF文件第4页浏览型号MIC2526-1BM的Datasheet PDF文件第5页浏览型号MIC2526-1BM的Datasheet PDF文件第6页浏览型号MIC2526-1BM的Datasheet PDF文件第7页浏览型号MIC2526-1BM的Datasheet PDF文件第8页浏览型号MIC2526-1BM的Datasheet PDF文件第9页  
MIC2526
Micrel
MIC2526
Dual USB Power Control Switch
Not Recommended for New Designs
Refer to MIC2026
General Description
The MIC2526 is a dual integrated high-side power switch with
independent enable and flag functions, optimized for self-
powered and bus-powered Universal Serial Bus (USB) appli-
cations. Few external components are necessary to satisfy
USB requirements.
The MIC2526 satisfies the following USB requirements: each
switch channel supplies up to 500mA as required by USB
downstream devices; the switch’s low on-resistance meets
USB voltage drop requirements; fault current is limited to
typically 750mA, well below the UL 25VA safety require-
ments; and a flag output is available to indicate fault condi-
tions to the local USB controller. Soft start eliminates the
momentary voltage drop on the upstream port that may occur
when the switch is enabled in bus-powered applications.
Additional features include thermal shutdown to prevent
catastrophic switch failure from high-current loads,
undervoltage lockout (UVLO) to ensure that the device re-
mains off unless there is a valid input voltage present, and
3.3V and 5V logic compatible enable inputs.
The MIC2526 is available in active-high and active-low ver-
sions in 8-pin DIP and SOIC packages.
Features
Compliant to USB specifications
UL Recognized Component
2 independent switches
3V to 5.5V input
500mA minimum continuous load current per port
140mΩ maximum on-resistance
1.25A maximum short circuit current limit
Individual open-drain fault flag pins
110µA typical on-state supply current
1µA typical off-state supply current
Output can be forced higher than input (off-state)
Thermal shutdown
2.4V typical undervoltage lockout (UVLO)
1ms turn-on (soft-start) and fast turnoff
Active-high or active-low enable versions
8-pin SOIC and DIP packages
USB host and self-powered hubs
USB bus-powered hubs
Hot plug-in power supplies
Battery-charger circuits
Applications
Typical Application
V
CC
5.0V
10k
4.50V to 5.25V
Upstream V
BUS
100mA max.
V
BUS
D+
D–
GND
1µF
10k
MIC5207-3.3
IN
OUT
GND
1µF
3.3V USB Controller
VIN
ON/OFF
OVERCURRENT
OVERCURRENT
ON/OFF
100k
100k
MIC2526-2
ENA
FLGA
FLGB
ENB
OUTA
IN
GND
OUTB
47µF
Data
Data
(Two Pair)
to USB
Controller
47µF
0.1µF
V
BUS
D+
D–
GND
USB
Port 2
Ferrite
Beads
V
BUS
D+
D–
GND
USB
Port 1
2-Port USB Self-Powered Hub
UL Recognized Component
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com
February 2000
1
MIC2526