W3E32M64S-XSBX
White Electronic Designs
NOTES:
16. Inputs are not recognized as valid until VREF stabilizes once initialized, including
SELF REFRESH mode, VREF must be powered within specified range. Exception:
during the period before VREF stabilizes, CKE ≤ 0.3 x VCCQ is recognized as LOW.
17. The output timing reference level, as measured at the timing reference point
1. All voltages referenced to VSS
.
2. Tests for AC timing, ICC, and electrical AC and DC characteristics may be
conducted at nominal reference/supply voltage levels, but the related specifications
and device operation are guaranteed for the full voltage range specified.
3. Outputs measured with equivalent load:
indicated in Note 3, is VTT
tHZ and tLZ transitions occur in the same access time windows as valid data
.
18.
transitions. These parameters are not referenced to a specific voltage level, but
specify when the device output is no longer driving (HZ) or begins driving (LZ).
19. The intent of the Don't Care state after completion of the postamble is the DQS-
driven signal should either be high, low, or high-Z and that any signal transition
within the input switching region must follow valid input requirements. That is, if
DQS transitions high (above VIHDC (MIN) then it must not transition low (below
V
TT
50Ω
Output
(VOUT
)
4. AC timing and ICC tests may use a VIL-to-VIH swing of up to 1.5V in the test
environment, but input timing is still referenced to VREF (or to the crossing point for
CK/CK#), and parameter specifications are guaranteed for the specified AC input
levels under normal use conditions. The minimum slew rate for the input signals
used to test the device is 1V/ns in the range between VIL (AC) and VIH (AC).
5. The AC and DC input level specifications are as defined in the SSTL_2 Standard
(i.e., the receiver will effectively switch as a result of the signal crossing the AC
input level, and will remain in that state as long as the signal does not ring back
above [below] the DC input LOW [HIGH] level).
VIHDC) prior to tDQSH (MIN).
20. This is not a device limit. The device will operate with a negative value, but system
performance could be degraded due to bus turnaround.
21. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE
command. The case shown (DQS going from High-Z to logic LOW) applies when
no WRITEs were previously in progress on the bus. If a previous WRITE was in
6.
V
REF is expected to equal VCCQ/2 of the transmitting device and to track variations in
progress, DQS could be HIGH during this time, depending on tDQSS.
the DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not
exceed ±2 percent of the DC value. Thus, from VCCQ/2, VREF is allowed ±25mV for
DC error and an additional ±25mV for AC noise. This measurement is to be taken
at the nearest VREF by-pass capacitor.
22. MIN (tRC or tRFC) for ICC measurements is the smallest multiple of tCK that meets
the minimum absolute value for the respective parameter. tRAS (MAX) for ICC
measurements is the largest multiple of tCK that meets the maximum absolute value
for tRAS
.
7.
8.
V
TT is not applied directly to the device. VTT is a system supply for signal
termination resistors, is expected to be set equal to VREF and must track variations
in the DC level of VREF
ID is the magnitude of the difference between the input level on CK and the input
level on CK#.
23. The refresh period 64ms. This equates to an average refresh rate of 7.8125μs.
However, an AUTO REFRESH command must be asserted at least once every
70.3μs; burst refreshing or posting by the DRAM controller greater than eight
refresh cycles is not allowed.
24. The I/O capacitance per DQS and DQ byte/group will not differ by more than this
maximum amount for any given device.
.
V
9. The value of VIX and VMP are expected to equal VCCQ/2 of the transmitting device
and must track variations in the DC level of the same.
25. The valid data window is derived by achieving other specifications - tHP (tCK/2),
10.
I
CC is dependent on output loading and cycle rates. Specified values are obtained
with minimum cycle time with the outputs open.
11. Enables on-chip refresh and address counters.
12. CC specifications are tested after the device is properly initialized, and is averaged
at the defined cycle rate.
tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates directly porportional
with the clock duty cycle and a practical data valid window can be derived. The
clock is allowed a maximum duty cycle variation of 45/55. Functionality is uncertain
when operating beyond a 45/55 ratio. The data valid window derating curves are
provided below for duty cycles ranging between 50/50 and 45/55.
26. Referenced to each output group: LDQS with DQ0-DQ7; and UDQS with DQ8-
DQ15 of each chip.
27. This limit is actually a nominal value and does not result in a fail value. CKE is
HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during
standby).
I
13. This parameter is not tested but guaranteed by design. tA = 25°C, f = 1 MHz
14. For slew rates less than 1V/ns and greater than or equal to 0.5 V.ns. If the slew rate
is less than 0.5V/ns, timing must be derated: tIS has an additional 50 ps per each
100mV/ns reduction in slew rate from the 500mV/ns. tIH has 0ps added, that is, it
remains constant. If the slew rate exceeds 4.5V/ns, functionality is uncertain.
15. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at
which CK and CK# cross; the input reference level for signals other than CK/CK# is
VREF
.
FIGURE A – PULL-DOWN CHARACTERISTICS
160
FIGURE B – PULL-UP CHARACTERISTICS
0
Maximum
-20
140
Minimum
-40
120
-60
-80
Nominal low
Nominal high
Nominal high
100
80
-100
-120
-140
-160
-180
-200
Nominal low
60
Minimum
40
20
0
Maximum
0.0
0.5
1.0
1.5
2.0
2.5
0.0
0.5
1.0
1.5
2.0
2.5
VCCQ - VOUT (V)
VOUT (V)
January 2008
Rev. 6
13
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com