SC70, Single/Dual Low-Voltage,
Low-Power µP Reset Circuits
Detailed Description
Reset Thresholds (-40°C to +125°C)
SUFFIX
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
V
(min)
V
(nom)
V
(max)
TH
RESET Output
A µP reset input starts the µP in a known state. These
µP supervisory circuits assert reset to prevent code
execution errors during power-up, power-down, or
brownout conditions.
TH
TH
4.51
4.63
4.74
4.39
4.27
4.19
4.10
4.00
3.90
3.80
3.71
3.61
3.51
3.41
3.32
3.22
3.12
3.00
2.93
2.85
2.73
2.63
2.56
2.44
2.34
2.26
2.13
2.05
1.95
1.85
1.76
1.62
1.54
4.50
4.38
4.30
4.20
4.10
4.00
3.90
3.80
3.70
3.60
3.50
3.40
3.30
3.20
3.08
3.00
2.93
2.80
2.70
2.63
2.50
2.40
2.31
2.19
2.10
2.00
1.90
1.80
1.67
1.58
4.61
4.48
4.41
4.31
4.20
4.10
4.00
3.90
3.79
3.69
3.59
3.49
3.38
3.28
3.15
3.08
3.00
2.87
2.77
2.69
2.56
2.46
2.37
2.24
2.15
2.05
1.95
1.85
1.71
1.61
Reset asserts when V
is below the reset threshold;
CC
once V
exceeds the reset threshold, an internal timer
CC
keeps the reset output asserted for the reset timeout
period. After this interval, reset output deasserts. Reset
output is guaranteed to be in the correct logic state for
V
CC
≥ 1V.
Manual Reset Input (MAX6384/
MAX6385/MAX6386/MAX6390)
Many µP-based products require manual reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic low on MR
asserts reset. Reset remains asserted while MR is low,
and for the reset active timeout period (t ) after MR
RP
returns high. This input has an internal 63kΩ pullup
resistor (1.35kΩ for MAX6390), so it can be left uncon-
nected if it is not used. MR can be driven with TTL or
CMOS logic levels, or with open-drain/collector outputs.
Connect a normally open momentary switch from MR to
GND to create a manual-reset function; external
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environ-
ment, connecting a 0.1µF capacitor from MR to GND
provides additional noise immunity.
RESET IN Comparator
(MAX6387/MAX6388/MAX6389)
RESET IN is compared to an internal +1.27V reference.
If the voltage at RESET IN is less than 1.27V, reset
asserts. Use the RESET IN comparator as a user-
adjustable reset detector or as a secondary power-sup-
ply monitor by implementing a resistor-divider at RESET
IN (shown in Figure 1). Reset asserts when either V
CC
or RESET IN falls below its respective threshold volt-
age. Use the following equation to set the threshold:
V
= V
(R1/R2 + 1)
INTH
THRST
___________Applications Information
where V
= +1.27V. To simplify the resistor selec-
THRST
Negative-Going V
CC
Transients
tion, choose a value of R2 and calculate R1:
In addition to issuing a reset to the µP during power-up,
power-down, and brownout conditions, the
MAX6381–MAX6390 are relatively immune to short dura-
R1 = R2 [(V /V ) - 1]
INTH THRST
Since the input current at RESET IN is 50nA (max),
large values can be used for R2 with no significant loss
in accuracy.
tion negative-going V transients (glitches).
CC
The Typical Operating Characteristics section shows the
Maximum Transient Durations vs. Reset Comparator
Overdrive, for which the MAX6381–MAX6390 do not
generate a reset pulse. This graph was generated using
6
_______________________________________________________________________________________
MAXIM [ MAXIM INTEGRATED PRODUCTS ]
