Electrical and Thermal Characteristics
Table 3ꢀ Electrical and thermal characteristics for LUXE ON C Color Line at 350mA, Tj=85ºCꢀ
ForWard VoltaGe [1] (Vf)
tyPIcal temPerature
coeFFIcIent oF ForWard
VoltaGe [2] (ꢅV/°c)
tyPIcal tHermal
resIstance—JunctIon
to solder Pad (°c/W)
color
Part numBer
mInImum tyPIcal maXImum
Far Red
Deep Red
Red
L1C1-FRD1000000000
L1C1-DRD1000000000
L1C1-RED1000000000
L1C1-RNG1000000000
L1C1-AMB1000000000
L1C1-PCA1000000000
L1C1-MNT1000000000
L1C1-LME1000000000
L1C1-GRN1000000000
L1C1-CYN1000000000
L1C1-BLU1000000000
L1C1-RYL1000000000
L1C1-VLT1000000000
L1C1-xxx0000000000
1.50
1.50
1.75
1.75
1.75
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
1.90
2.05
2.00
2.05
2.05
2.75
2.75
2.75
3.05
3.05
2.84
2.75
2.83
2.75
2.30
2.30
2.50
2.50
2.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
-1.7
-1.7
-1.6
-1.6
-2.0
-1.7
-2.7
-2.7
-2.4
-2.4
-2.6
-1.7
-1.7
-1.7
2.8
2.8
2.8
2.8
2.8
3.0
2.8
2.8
3.5
3.5
3.5
2.8
3.8
2.8
Red-Orange
Amber
PC Amber
Mint
Lime
Green
Cyan
Blue
Royal Blue
Violet
White
Notes for Table 3:
1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.
2. Measured between 25°C and 85°C.
Absolute Maximum Ratings
Table 4ꢀ Absolute maximum ratings for LUXEON C Color Lineꢀ
Far red
Parameter
red, red-oranGe,
Green
Blue and
royal Blue
mInt, lIme, VIolet
and WHIte
and deeP red
amBer and Pc amBer and cyan
DC Forward Current[1, 2]
Peak Pulsed Forward Current[1, 3]
LED Junction Temperature[1] (DC & Pulse)
700mA
875mA
135°C
1050mA
1300mA
120°C
1050mA
1300mA
135°C
1050mA
1300mA
135°C
1225mA
1500mA
135°C
ESD Sensitivity
(ANSI/ESDA/JEDEC JS-001-2012)
Class 3B
LED Storage Temperature
Soldering Temperature
Allowable Reflow Cycles
-40°C to 135°C
JEDEC 020c 260°C
3
Reverse Voltage (Vreverse
)
LUXEON C LEDs are not designed to be driven in reverse bias
Notes for Table 4:
1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature.
2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met:
– The frequency of the ripple current is 100Hz or higher
– The average current for each cycle does not exceed the maximum allowable DC forward current
– The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current
3. At 10% duty cycle with pulse width of 10ms.
DS144 LUXEON C Color Line Product Datasheet 20210826 ©2021 Lumileds Holding B.V. All rights reserved.
5
LUMILEDS [ LUMILEDS LIGHTING COMPANY ]
