LT1763 Series
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2)
PARAMETER
CONDITIONS
= 7V, V = 0V
OUT
MIN
TYP
MAX
UNITS
Current Limit
V
IN
l
l
C, I Grade: V = V
+ 1V or 2.3V (Note 12), ΔV = –0.1V
OUT
520
520
mA
mA
IN
OUT(NOMINAL)
MP Grade: V = 2.35V (Note 12), ΔV
= –0.1V
IN
OUT
l
Input Reverse Leakage Current
V
IN
= –20V, V
= 0V
1
mA
OUT
Reverse Output Current
(Note 10)
LT1763-1.5
LT1763-1.8
LT1763-2.5
LT1763-3
V
V
V
V
V
V
V
= 1.5V, V < 1.5V
10
10
10
10
10
10
5
20
20
20
20
20
20
10
μA
μA
μA
μA
μA
μA
μA
OUT
OUT
OUT
OUT
OUT
OUT
OUT
IN
= 1.8V, V < 1.8V
IN
= 2.5V, V < 2.5V
IN
= 3V, V < 3V
IN
LT1763-3.3
LT1763-5
= 3.3V, V < 3.3V
IN
= 5V, V < 5V
IN
LT1763 (Note 3)
= 1.22V, V < 1.22V
IN
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage will be equal to: V – V
.
IN
DROPOUT
Note 7: GND pin current is tested with V = V
or V = 2.3V
IN
IN
OUT(NOMINAL)
Note 2: The LT1763 regulators are tested and specified under pulse
(C, I grade) or 2.35V (MP grade), whichever is greater, and a current
source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
Note 8: ADJ pin bias current flows into the ADJ pin.
Note 9: SHDN pin current flows into the SHDN pin.
Note 10: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out the GND pin.
load conditions such that T ≅ T . The LT1763 (C grade) is 100% tested
J
A
at T = 25°C; performance at –40°C and 125°C is assured by design,
A
characterization and correlation with statistical process controls. The
LT1763 (I grade) is guaranteed over the full –40°C to 125°C operating
junction temperature range. The LT1763 (MP grade) is 100% tested and
guaranteed over the –55°C to 125°C operating junction temperature range.
Note 3: The LT1763 (adjustable version) is tested and specified for these
conditions with the ADJ pin connected to the OUT pin.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 5: To satisfy requirements for minimum input voltage, the LT1763
(adjustable version) is tested and specified for these conditions with an
external resistor divider (two 250k resistors) for an output voltage of
2.44V. The external resistor divider will add a 5μA DC load on the output.
Note 11: For the LT1763, LT1763-1.5 and LT1763-1.8 dropout voltage will
be limited by the minimum input voltage specification under some output
voltage/load conditions. See the curve of Minimum Input Voltage in the
Typical Performance Characteristics.
Note 12: To satisfy requirements for minimum input voltage, current limit
is tested at V = V
+ 1V or 2.3V (C, I grade) or 2.35V
IN
OUT(NOMINAL)
(MP grade), whichever is greater.
1763fg
6
Linear [ Linear ]
