LT1304/LT1304-3.3/LT1304-5
U
OPERATIO
tion in efficiency. For the majority of 2-cell or 3-cell input
LT1304 applications, a 22µH or 20µH inductor such as the
SumidaCD54-220(drum)orCoiltronicsCTX20-1(toroid)
will suffice. If switch current is reduced using the ILIM pin,
smaller inductors such as the Sumida CD43 series or
Coilcraft DO1608 series can be used. Minimizing DCR is
important for best efficiency. Ideally, the inductor DCR
should be less than 0.05Ω, although the physical size of
such an inductor makes its use prohibitive in many space
conscious applications. If EMI is a concern, such as when
sensitive analog circuitry is present, a toroidal inductor
such as the Coiltronics CTX20-1 is suggested.
The LT1304’s operation can best be understood by exam-
ining the block diagram in Figure 1. Comparator A1
monitors the output voltage via resistor divider string
R3/R4 at the FB pin. When VFB is higher than the 1.24V
reference, A2 and the timers are turned off. Only the
reference, A1 and A3 consume current, typically 120µA.
As VFB drops below 1.24V plus A1’s hysteresis (about
6mV), A1 enables the rest of the circuit. Power switch Q1
is then cycled on for 6µs, or until current comparator A2
turns off the ON timer, whichever comes first. Off-time is
fixed at approximately 1.5µs. Q1’s switching causes cur-
rent to alternately build up in inductor L1 and discharge
into output capacitor C2 via D1, increasing the output
voltage. As VFB increases enough to overcome C1’s hys-
teresis, switching action ceases. C2 is left to supply
current to the load until VOUT decreases enough to force
A1’s output high, and the entire cycle repeats.
A special case exists where the VOUT/VIN differential is
high, such as a 2V to 12V boost converter. If the required
duty cycle for continuous mode operation is higher than
the LT1304 can provide, the converter must be designed
for discontinuous operation. This means that the inductor
current decreases to zero during the switch OFF time. For
a simple step-up (boost) converter, duty cycle can be
calculated by the following formula:
If switch current reaches 1A, causing A2 to trip, switch
ON time is reduced. This allows continuous mode opera-
tion during bursts. A2 monitors the voltage across 7.2Ω
resistor R1, which is directly related to the switch current.
Q2’s collector current is set by the emitter-area ratio to
0.5% of Q1’s collector current. R1’s voltage drop exceeds
36mV, corresponding to 1A switch current, A2’s output
goes high, truncating the ON time part of the switch cycle.
The 1A peak current can be reduced by tying a resistor
between the ILIM pin and ground, causing a voltage drop
to appear across R2. The drop offsets some of the 36mV
reference voltage, lowering peak current. A 22k resistor
limits current to approximately 550mA. A capacitor con-
nected between ILIM and ground provides soft start. Shut-
down is accomplished by grounding the SHDN pin.
DC = 1 – [(VIN – VSAT)/(VOUT + VD)]
where,
VIN = Minimum input voltage
VSAT = Switch saturation voltage (0.3V)
VOUT = Output voltage
VD = Diode forward voltage (0.4V)
If the calculated duty cycle exceeds the minimum LT1304
duty cycle of 76%, the converter should be designed for
discontinuous mode operation. The inductance must be
low enough so that current in the inductor reaches the
peak current in a single cycle. Inductor value can be
calculated by:
The low-battery detector A3 has its own 1.17V reference
andisalwayson.Theopencollectoroutputdevicecansink
up to 500µA. Approximately 35mV of hysteresis is built
into A3 to reduce “buzzing” as the battery voltage reaches
the trip level.
L = (VIN – VSAT)(tON/1A)
where,
tON = Minimum on-time of LT1304 (4µs)
Inductor Selection
One advantage of discontinuous mode operation is that
inductor values are usually quite low so very small units
can be used. Ripple current is higher than with continuous
mode designs and efficiency will be somewhat less.
Inductors used with the LT1304 must be capable of
handling the worst-case peak switch current of 1.2A
without saturating. Open flux rod or drum core units may
be biased into saturation by 20% with only a small reduc-
6
Linear [ Linear ]
