欢迎访问ic37.com |
会员登录 免费注册
发布采购

LT1085CM#TRPBF 参数 Datasheet PDF下载

LT1085CM#TRPBF图片预览
型号: LT1085CM#TRPBF
PDF下载: 下载PDF文件 查看货源
内容描述: [LT1085 - 7.5A, 5A, 3A Low Dropout Positive Adjustable Regulators; Package: DD PAK; Pins: 3; Temperature Range: 0°C to 70°C]
分类和应用: 输出元件调节器
文件页数/大小: 22 页 / 285 K
品牌: Linear [ Linear ]
 浏览型号LT1085CM#TRPBF的Datasheet PDF文件第6页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第7页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第8页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第9页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第11页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第12页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第13页浏览型号LT1085CM#TRPBF的Datasheet PDF文件第14页  
LT1083/LT1084/LT1085  
block DiagraM  
V
IN  
+
THERMAL  
LIMIT  
V
OUT  
1083/4/5 ADJ BD  
V
ADJ  
applicaTions inForMaTion  
The LT1083 family of 3-terminal adjustable regulators is  
easy to use and has all the protection features that are  
expectedinhighperformancevoltageregulators.Theyare  
short-circuit protected, and have safe area protection as  
well as thermal shutdown to turn off the regulator should  
the junction temperature exceed about 165°C.  
on the output will ensure stability. Normally, capacitors  
muchsmallerthanthiscanbeusedwiththeLT1083.Many  
different types of capacitors with widely varying charac-  
teristics are available. These capacitors differ in capacitor  
tolerance (sometimes ranging up to 100%), equivalent  
seriesresistance,andcapacitancetemperaturecoefficient.  
The 150µF or 22µF values given will ensure stability.  
These regulators are pin compatible with older 3-terminal  
adjustable devices, offer lower dropout voltage and more  
precisereferencetolerance.Further,thereferencestability  
with temperature is improved over older types of regula-  
tors. The only circuit difference between using the LT1083  
family and older regulators is that this new family requires  
an output capacitor for stability.  
When the adjustment terminal is bypassed to improve the  
ripple rejection, the requirement for an output capacitor  
increases. The value of 22µF tantalum or 150µF aluminum  
covers all cases of bypassing the adjustment terminal.  
Without bypassing the adjustment terminal, smaller  
capacitors can be used with equally good results and the  
table below shows approximately what size capacitors are  
needed to ensure stability.  
Stability  
The circuit design used in the LT1083 family requires the  
use of an output capacitor as part of the device frequency  
compensation.Foralloperatingconditions,theadditionof  
a 150µF aluminium electrolytic or a 22µF solid tantalum  
Recommended Capacitor Values  
INPUT  
OUTPUT  
ADJUSTMENT  
10µF  
10µF  
10µF Tantalum, 50µF Aluminum  
22µF Tantalum, 150µF Aluminum  
None  
20µF  
108345fh  
10  
For more information www.linear.com/LT1083