LT6003/LT6004/LT6005
APPLICATIONS INFORMATION
Supply Voltage
+
beta of the PNP input transistors. As V approaches V
CM
devices in the cancellation circuitry saturate causing I to
B
The positive supply of the LT6003/LT6004/LT6005 should
be bypassed with a small capacitor (about 0.01μF) within
an inch of the pin. When driving heavy loads, an additional
4.7μF electrolytic capacitor should be used. When using
split supplies, the same is true for the negative supply pin.
increase(inthenanoamprange).Inputoffsetvoltageerrors
due to I can be minimized by equalizing the noninverting
B
and inverting source impedances.
The input offset voltage changes depending on which
input stage is active; input offset voltage is trimmed on
both input stages, and is guaranteed to be 500μV max in
the PNP stage. By trimming the input offset voltage of
both input stages, the input offset voltage shift over the
entire common mode range (CMRR) is typically 160μV,
maintaining the precision characteristics of the amplifier.
Rail-to-Rail Characteristics
TheLT6003/LT6004/LT6005arefullyfunctionalforaninput
signal range from the negative supply to the positive sup-
ply. Figure 1 shows a simplified schematic of the amplifier.
The input stage consists of two differential amplifiers, a
PNP stage Q3/Q6 and an NPN stage Q4/ Q5 that are active
over different ranges of the input common mode voltage.
The PNP stage is active for common mode voltages,
The input stage of the LT6003/LT6004/LT6005 incorpo-
rates phase reversal protection to prevent wrong polarity
outputs from occurring when the inputs are driven up to
9V below the negative rail. 600k protective resistors are
includedintheinputleadssothatcurrentdoesnotbecome
V
, between the negative supply to approximately 0.9V
CM
below the positive supply. As V moves closer towards
CM
–
the positive supply, the transistor Q7 will steer Q2’s tail
current to the current mirror Q8/Q9, activating the NPN
differential pair. The PNP pair becomes inactive for the
rest of the input common mode voltage range up to the
positive supply.
excessive when the inputs are forced below V or when
a large differential signal is applied. Input current should
be limited to 10mA when the inputs are driven above the
positive rail.
Output
The second stage is a folded cascode and current mir-
ror that converts the input stage differential signals into
a single ended output. Capacitor C1 reduces the unity
cross frequency and improves the frequency stability
without degrading the gain bandwidth of the amplifier.
The complementary drive generator supplies current to
the output transistors that swing from rail to rail.
The output of the LT6003/LT6004/LT6005 is guaranteed to
swing within 100mV of the positive rail and 50mV of the
negative rail with no load, over the industrial temperature
range. The LT6003/LT6004/LT6005 can typically source
8mA on a single 5V supply. Sourcing current is reduced
to 5mA on a single 1.8V supply as noted in the electrical
characteristics.However,whensourcingmorethan250μA
with an output load impedance greater than 20kΩ, a 1μF
capacitor in series with a 2k resistor should be placed
from the output to ground to insure stability.
Input
Input bias current (I ) is minimized with cancellation
B
circuitry on both input stages. The cancellation circuitry
remains active when V is more than 300mV from either
The normally reverse-biased substrate diode from the
CM
–
–
rail. As V approaches V the cancellation circuitry turns
output to V will cause unlimited currents to flow when
CM
–
off and I is determined by the tail current of Q2 and the
the output is forced below V . If the current is transient
B
and limited to 100mA, no damage will occur.
600345fd
13
LINEAR_DIMENSIONS [ Linear Dimensions ]
