LTC1857/LTC1858/LTC1859
W U U
U
APPLICATIO S I FOR ATIO
OVERVIEW
Before starting a conversion, an 8-bit data word is clocked
into the SDI input on the first eight rising SCK edges to
select the MUX address, input range and power down
mode. The ADC enters acquisition mode on the falling
edge of the sixth clock in the 8-bit data word and ends on
the rising edge of the CONVST signal which also starts a
conversion (see Figure 7). A minimum time of 4µs will
provide enough time for the sample-and-hold capacitors
to acquire the analog signal. Once a conversion cycle has
begun, it cannot be restarted.
The LTC1857/LTC1858/LTC1859 are innovative, multi-
channelADCsthatprovidesoftware-selectableinputranges
for each of their eight input channels. Using on-chip
resistors and switches, it provides an attenuation and
offset that can be programmed for each channel on the fly.
The precisely trimmed attenuators ensure accurate input
ranges. Because they precede the multiplexer, errors due
to multiplexer on-resistance are eliminated.
The input word that selects the input channel also selects
the desired input range for that channel. The available
ranges are 0V to 5V, 0V to 10V (unipolar), ±5V and ±10V
(bipolar). They are achieved with the ADC running on a
single 5V supply. In addition to the range selection, single
ended or differential inputs may be selected for each
channel or pair of channels. Finally, overrange protection
is provided for unselected channels. An overrange condi-
tion on an unused channel will not affect the conversion
result on the selected channel.
During the conversion, the internal differential 12-/14-/
16-bitcapacitiveDACoutputissequencedbytheSARfrom
the most significant bit (MSB) to the least significant bit
(LSB). The input is successively compared with the binary
weighted charges supplied by the differential capacitive
DAC. Bit decisions are made by a high speed comparator.
At the end of a conversion, the DAC output balances the
analog input (ADC+ – ADC–). The SAR contents (a 16-bit
data word) which represents the difference of ADC+ and
ADC– are loaded into the 12-/14-/16-bit shift register.
CONVERSION DETAILS
DRIVING THE ANALOG INPUTS
TheLTC1857/LTC1858/LTC1859useasuccessiveapproxi-
mation algorithm and an internal sample-and-hold circuit
to convert an analog signal to a 12-/14-/16-bit serial out-
put respectively. The ADCs are complete with a precision
reference and an internal clock. The control logic provides
easyinterfacetomicroprocessorsandDSPs.(Pleaserefer
to the Digital Interface section for the data format.)
The nominal input ranges for the LTC1857/LTC1858/
LTC1859 are 0V to 5V, 0V to 10V, ±5V and ±10V and the
MUX inputs are overvoltage protected to ±25V. The input
impedance is typically 42kΩ in unipolar mode and 31kΩ
in bipolar mode, therefore, it should be driven with a low
impedance source. Wideband noise coupling into the
input can be minimized by placing a 3000pF capacitor at
the input as shown in Figure 2. An NPO-type capacitor
gives the lowest distortion. Place the capacitor as close to
thedeviceinputpinaspossible.Ifanamplifieristobeused
to drive the input, care should be taken to select an
amplifier with adequate accuracy, linearity and noise for
the application. The following list is a summary of the op
amps that are suitable for driving the LTC1857/LTC1858/
LTC1859. More detailed information is available in the
Linear Technology data books and online at
www.linear.com.
The analog signals applied at the MUX input channels are
rescaled by the resistor divider network formed by R1, R2
and R3 as shown below. The rescaled signals appear on
theMUXOUT(Pins10,11)whicharealsoconnectedtothe
ADC inputs (Pins 12, 13) under normal operation.
REFCOMP
BIPOLAR
R3
10k
R1
25k
CH SEL
MUX
INPUT
MUXOUT
LT®1007: Low noise precision amplifier. 2.7mA supply
current ±5V to ±15V supplies. Gain bandwidth product
8MHz. DC applications.
R2
17k
1859 AI03
185789f
10
Linear Systems [ Linear Systems ]
