LT1180A/LT1181A
ELECTRICAL CHARACTERISTICS
PARAMETER
ON/OFF Pin Current
Oscillator Frequency
Driver
Output Voltage Swing
Logic Input Voltage Level
Input High Level (V
OUT
= Low)
Logic Input Current
Output Short-Circuit Current
Output Leakage Current
Date Rate (Note 7)
Slew Rate
R
L
= 3k, C
L
= 2500pF
Propagation Delay
Receiver
Input Voltage Thresholds
Load = 3k to GND
CONDITIONS
0V
≤
V
ON/OFF
≤
5V
The
q
denotes specifications which apply over the operating temperature
range (0°C
≤
T
A
≤
70°C for commercial grade, and – 40°C
≤
T
A
≤
85°C for industrial grade. (Note 2)
MIN
q
TYP
130
MAX
80
UNITS
µA
kHz
V
V
V
V
µA
mA
µA
kBaud
kBaud
– 15
Positive
Negative
5.0
q
q
q
q
7.5
– 6.3
1.4
1.4
5
17
10
– 5.0
0.8
20
100
Input Low Level (V
OUT
= High)
0.8V
≤
V
IN
≤
2.0V
V
OUT
= 0V
Shutdown V
OUT
=
±30V
(Note 4)
R
L
= 3k, C
L
= 2500pF
R
L
= 3k, C
L
= 1000pF
R
L
= 3k, C
L
= 51pF
2.0
±9
q
120
250
4
15
7
0.6
0.5
q
q
q
q
q
30
1.3
1.3
V/µs
V/µs
µs
µs
V
V
V
V
V
kΩ
µA
V
V
mA
ns
ns
Output Transition t
HL
High-to-Low (Note 5)
Output Transition t
LH
Low-to-High
Input Low Threshold (V
OUT
= High)
Input High Threshold (V
OUT
= Low)
Input LowI,
Input HighI,
C Grade
C Grade
M Grade
M Grade
0.8
0.2
0.1
3
q
q
q
1.3
1.7
1.3
1.7
0.4
5
1
0.2
4.2
–20
20
250
350
2.4
3.0
1.0
7
10
0.4
– 10
mA
600
600
Hysteresis
Input Resistance
Output Leakage Current
Output Voltage
Output Short-Circuit Current
Propagation Delay
V
IN
=
±10V
Shutdown (Note 4) 0
≤
V
OUT
≤
V
CC
Output Low, I
OUT
= – 1.6mA
Output High, I
OUT
= 160µA (V
CC
= 5V)
Sinking Current, V
OUT
= V
CC
Sourcing Current, V
OUT
= 0V
Output Transition t
HL
High-to-Low (Note 6)
Output Transition t
LH
Low-to-High
3.5
10
Note 1:
Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2:
Testing done at V
CC
= 5V and V
ON/OFF
= 3V, unless otherwise
specified.
Note 3:
Supply current is measured as the average over several charge
pump cycles. C
+
= C
–
= C1 = C2 = 0.1µF. All outputs are open, with all
driver inputs tied high.
Note 4:
Supply current measurements in SHUTDOWN are performed with
V
ON/OFF
≤
0.1V.
Note 5:
For driver delay measurements, R
L
= 3k and C
L
= 51pF. Trigger
points are set between the driver’s input logic threshold and the output
transition to the zero crossing (t
HL
= 1.4V to 0V and t
LH
= 1.4V to 0V).
Note 6:
For receiver delay measurements, C
L
= 51pF. Trigger points are
set between the receiver’s input logic threshold and the output transition
to standard TTL/CMOS logic threshold (t
HL
= 1.3V to 2.4V and t
LH
= 1.7V
to 0.8V).
Note 7:
Data rate operation guaranteed by slew rate, short-circuit current
and propagation delay tests.
11801afb
3