欢迎访问ic37.com |
会员登录 免费注册
发布采购

NSR060A0X43Z 参数 Datasheet PDF下载

NSR060A0X43Z图片预览
型号: NSR060A0X43Z
PDF下载: 下载PDF文件 查看货源
内容描述: 5 - 13.8VDC输入; 0.6Vdc至5.0VDC输出; 60A的输出电流 [5 - 13.8Vdc input; 0.6Vdc to 5.0Vdc Output; 60A output current]
分类和应用:
文件页数/大小: 18 页 / 772 K
品牌: LINEAGEPOWER [ LINEAGE POWER CORPORATION ]
 浏览型号NSR060A0X43Z的Datasheet PDF文件第9页浏览型号NSR060A0X43Z的Datasheet PDF文件第10页浏览型号NSR060A0X43Z的Datasheet PDF文件第11页浏览型号NSR060A0X43Z的Datasheet PDF文件第12页浏览型号NSR060A0X43Z的Datasheet PDF文件第14页浏览型号NSR060A0X43Z的Datasheet PDF文件第15页浏览型号NSR060A0X43Z的Datasheet PDF文件第16页浏览型号NSR060A0X43Z的Datasheet PDF文件第17页  
Data Sheet  
Naos Raptor 60A: Non Isolated Power Modules  
September 27, 2009  
5 – 13.8Vdc input; 0.6Vdc to 5.0Vdc Output; 60A output current  
Power Good  
Table 2  
The Naos Raptor 60A power modules provide a  
Power Good Status signal that indicates whether or  
not the power module is functioning properly.  
VO, set (V)  
Rtrim ()  
0.6  
1.0  
1.2  
1.5  
1.8  
2.5  
3.3  
5.0  
Open  
3000  
2000  
1333  
1000  
632  
PwGood is a power good signal implemented with an  
open-collector output to indicate that the output  
voltage is within the regulation limits of the power  
module. The PwGood signal will be de-asserted to a  
low state If any condition such as over-temperature,  
over-current, or over-voltage occurs which would  
result in the output voltage going out of range.  
444  
273  
Output Voltage Programming  
Monotonic Start-up and Shutdown  
The output voltage of the Naos Raptor 60A module  
can be programmed to any voltage from 0.6Vdc to  
5.0Vdc by connecting a resistor between the Trim +  
and Trim - pins of the module. Without an external  
resistor between Trim + and Trim - pins, the output of  
the module will be 0.6Vdc. To calculate the value of  
the trim resistor, Rtrim for a desired output voltage,  
use the following equation:  
The Naos Raptor 60A modules have monotonic start-  
up and shutdown behavior for any combination of  
rated input voltage, output current and operating  
temperature range.  
1.2  
Rtrim =  
kΩ  
(Vo 0.6)  
Rtrim is the external resistor in k  
Vo is the desired output voltage  
Table 2 provides Rtrim values required for some  
common output voltages.  
By using a ±0.1% tolerance trim resistor with a TC of  
±25ppm, a set point tolerance of ±0.8% can be  
achieved as specified in the electrical specification.  
The POL Programming Tool available at  
www.lineagepower.com under the Design Tools  
section, helps determine the required trim resistor  
needed for a specific output voltage.  
Note: Vin 180% of Vout at the module output pin.  
Vout  
VIN(+)  
VO(+)  
TRIM+  
ON/OFF  
LOAD  
R
trim  
TRIM  
GND  
Figure 42. Circuit configuration for programming  
output voltage using an external resistor.  
LINEAGE POWER  
13