欢迎访问ic37.com |
会员登录 免费注册
发布采购

JPW200S52R51-BHZ 参数 Datasheet PDF下载

JPW200S52R51-BHZ图片预览
型号: JPW200S52R51-BHZ
PDF下载: 下载PDF文件 查看货源
内容描述: 38伏直流 - 75 VDC输入, 52.5 Vdc输出; 200W [38 Vdc - 75 Vdc Input, 52.5 Vdc Output; 200W]
分类和应用:
文件页数/大小: 14 页 / 740 K
品牌: LINEAGEPOWER [ LINEAGE POWER CORPORATION ]
 浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第6页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第7页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第8页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第9页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第11页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第12页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第13页浏览型号JPW200S52R51-BHZ的Datasheet PDF文件第14页  
JPW200S52R5-BH Power Module; dc-dc Converter  
38 Vdc - 75 Vdc Input, 52.5 Vdc Output; 200W  
Data Sheet  
March 26, 2008  
Example  
Thermal Considerations  
What is the minimum airflow necessary for the  
JPW200S52R5-BH operating at VI = 52 V, an output current  
of 3.5 A, and a maximum ambient temperature of 40 °C?  
The power modules operate in a variety of thermal environ-  
ments; however, sufficient cooling should be provided to  
help ensure reliable operation of the unit. Heat-dissipating  
components inside the unit are thermally coupled to the  
base plate. Heat is removed by conduction, convection, and  
radiation to the surrounding environment. Proper cooling can  
be verified by measuring the base plate temperature. Peak  
temperature (TC) occurs at the position indicated in  
Figure 16.  
Solution  
Given: VI = 52 V  
IO = 3.5 A  
TA = 40 °C  
Determine airflow (v) (Use Figure 17.):  
v = 1.0 m (200 ft/min)  
MEASURE CASE  
TEMPERATURE HERE  
5.0  
4.5  
4.0  
3.5  
3.0  
VI  
(+)  
VO(+)  
2.5  
2.0  
1.5  
1.0  
0.5  
0.0  
ON/OFF  
CASE  
+ SEN  
TRIM  
– SEN  
33.02  
(1.30)  
VI  
(–)  
VO(–)  
20  
30  
40  
50  
60  
70  
80  
(°C)  
90  
6.35  
(0.25)  
LOCAL AMBIENT TEMPERATURE, T  
A
Figure 17. Derating Curve for JPW200S52R5-BH  
(Vo = 52.5V) with base plate; Vin = 52V.  
Note:Top view, pin locations are for reference only.  
Figure 16. Case Temperature Measurement Location.  
EMC Considerations  
For assistance with designing for EMC compliance, please  
refer to the FLTR100V10 data sheet  
(FDS01-043EPS).  
The temperature at this location should not exceed 100 °C.  
The output power of the module should not exceed the rated  
power for the module as listed in the Ordering Information  
table.  
Layout Considerations  
Although the maximum case temperature of the power mod-  
ules is 100 °C, you can limit this temperature to a lower  
value for extremely high reliability.  
Copper paths must not be routed beneath the power module  
mounting inserts. For additional layout guidelines, refer to  
the FLTR100V10 data sheet  
Heat Transfer Without Heat Sinks  
(DS98-152EPS).  
Increasing airflow over the module enhances the heat trans-  
fer via convection. Figure 17 shows the maximum output  
current that can be delivered by the module without exceed-  
ing the maximum case temperature versus local ambient  
temperature (TA) for natural convection through 3 m/s (600  
ft./min.).  
Note that the natural convection condition was measured at  
0.05 m/s to 0.1 m/s (10 ft./min. to 20 ft./min.); however, sys-  
tems in which these power modules may be used typically  
generate natural convection airflow rates of 0.3 m/s (60 ft./  
min.) due to other heat dissipating components in the sys-  
tem. The use of Figure 17 is shown in the following example.  
Lineage Power  
10