Data Sheet
GE
CP2725AC54TE CPL High Efficiency Rectifier
100-120/200-277VAC input; Default Outputs: ±54VDC @ 2725W, 5VDC @ 4W
Using the PCA9541 multiplexer: Transition between the two
Status Signals
I2C lines is provided by the industry standard PCA9541 I2C
master selector multiplexer. Option 01 of the device code is
supplied which, upon start-up, connects channel 0 to the
power supply. In this fashion applications using only a single
I2C line can immediately start talking across the bus without
first requiring to reconfigure the multiplexer.
Power Capacity: A HI on this pin indicates that the rectifier
delivers high line rated output power; a LO indicates that the
rectifier is connected to low line configured for 1200W
operation.
Power Fail Warning: This signal is HI when the main output is
being delivered and goes LO for the duration listed in this data
sheet prior to the output decaying below the listed voltage
level.
Fault: This signal goes LO for any failure that requires rectifier
replacement. These faults may be due to:
Fan failure
Over-temperature warning
Over-temperature shutdown
Over-voltage shutdown
Internal Rectifier Fault
Figure 14. Diagram showing conceptual representation
of the dual I2C bus system.
Digital Feature Descriptions
PMBus™ compliance: The power supply is fully compliant to
the Power Management Bus (PMBus™) rev1.2 requirements
with the following exceptions:
Control can be taken over at any time by a specific ‘master’
even during data transmission to the other ‘master’. The
‘master’ needs to be able to handle incomplete transmissions
in the multi-master environment in case switching should
commence in the middle of data transmission.
The power supply continuously updates its STATUS and ALARM
registers to the latest state in order to capture the ‘present’
state of the power supply. There are a number of indicators,
such as those indicating a communications fault (PEC error,
data error) that do not get cleared until specifically instructed
by the host controller sending a clear_faults command. A ‘bit’
indicator notifies the user if the STATUS and ALARM registers
changed since the last ‘read’ by the host controller.
Master/Slave: The ‘host controller’ is always the MASTER.
Power supplies are always SLAVES. SLAVES cannot initiate
communications or toggle the Clock. SLAVES also must
respond expeditiously at the command of the MASTER as
required by the clock pulses generated by the MASTER.
Clock stretching: The ‘slave’ µController inside the power
supply may initiate clock stretching if it is busy and it desires to
delay the initiation of any further communications. During the
clock stretch the ‘slave’ may keep the clock LO until it is ready
to receive further instructions from the host controller. The
maximum clock stretch interval is 25ms.
For example, if a voltage surge causes a momentary shutdown
for over voltage the power supply will automatically restart if
the ‘auto_restart’ feature is invoked. During the momentary
shutdown the power supply issues an Alert# indicating to the
system controller that a status change has occurred. If the
system controller reads back the STATUS and ALARM registers
while the power supply is shut down it will get the correct fault
condition. However, inquiry of the state of the power supply
after the restart event would indicate that the power supply is
functioning correctly. The STATUS and ALARM indicators did
not freeze at the original shutdown state and so the reason for
the original Alert# is erased. The restart ‘bit’ would be set to
indicate that an event has occurred.
The host controller needs to recognize this clock stretching,
and refrain from issuing the next clock signal, until the clock
line is released, or it needs to delay the next clock pulse
beyond the clock stretch interval of the power supply.
Note that clock stretching can only be performed after
completion of transmission of the 9th ACK bit, the exception
being the START command.
The power supply also clears the STATUS and ALARM registers
after a successful read back of the information in these
registers, with the exception of communications error alarms.
This automated process improves communications efficiency
since the host controller does not have to issue another
clear_faults command to clear these registers.
Dual, redundant buses: Two independent I2C lines provide
true communications bus redundancy and allow two
independent controllers to sequentially control the power
supply. For example, a short or an open connection in one of
the I2C lines does not affect communications capability on the
other I2C line. Failure of a ‘master’ controller does not affect the
power supplies and the second ‘master’ can take over control
at any time.
Clock
Stretch
Figure 14. Example waveforms showing clock stretching.
Communications speed: Both 100kHz and 400kHz clock rates
are supported. The power supplies default to the 100kHz clock
rate.
January 30, 2014
©2013 General Electric Company. All rights reserved.
Page 10
LINEAGEPOWER [ LINEAGE POWER CORPORATION ]
