Specifications
GAL22LV10D
Specifications
GAL22LV10
ABSOLUTE MAXIMUM RATINGS
(1)
Supply voltage V
CC
.................................... -0.5 to +4.6V
Input voltage applied ................................. -0.5 to +5.6V
I/O voltage applied .................................... -0.5 to +4.6V
Off-state output voltage applied................. -0.5 to +4.6V
Storage Temperature .................................. -65 to 150°C
Ambient Temperature with
Power Applied ......................................... -55 to 125°C
1.Stresses above those listed under the “Absolute Maximum
Ratings” may cause permanent damage to the device. These
are stress only ratings and functional operation of the device
at these or at any other conditions above those indicated in the
operational sections of this specification is not implied (while
programming, follow the programming specifications).
RECOMMENDED OPERATING COND.
Commercial Devices:
Ambient Temperature (T
A
) ............................... 0 to 75°C
Supply voltage (V
CC
)
with Respect to Ground ......................... +3.0 to +3.6V
DC ELECTRICAL CHARACTERISTICS
Over Recommended Operating Conditions (Unless Otherwise Specified)
SYMBOL
PARAMETER
Input Low Voltage
Input High Voltage
I/O High Voltage
CONDITION
MIN.
Vss - 0.3
2.0
2.0
0V
≤
V
IN
≤
V
IL
(MAX.)
(Vcc-0.2)V
≤
V
IN
≤
V
CC
Vcc
≤
V
IN
≤
5.25V
Vcc
≤
V
IN
≤
4.6V
I
OL
= MAX.
Vin
=
V
IL
or
V
IH
I
OL
= 500µA
Vin
=
V
IL
or
V
IH
—
—
—
—
—
—
2.4
Vcc-0.2V
—
—
V
CC
= 3.3V
V
OUT
= 0.5V T
A
= 25°C
-15
TYP.
3
—
—
—
—
—
—
—
—
—
—
—
—
—
—
MAX.
0.8
5.25
Vcc+0.5
-100
10
10
20
0.4
0.2
—
—
8
–8
-80
UNITS
V
V
V
µA
µA
µA
mA
V
V
V
V
mA
mA
mA
V
IL
V
IH
I
IL
1
I
IH
Input or I/O Low Leakage Current
Input or I/O High Leakage Current
Input High Leakage Current
I/O High Leakage Current
V
OL
V
OH
I
OL
I
OH
I
OS
2
Output Low Voltage
Output High Voltage
I
OH
= MAX.
Vin
=
V
IL
or
V
IH
I
OH
= -100µA
Vin
=
V
IL
or
V
IH
Low Level Output Current
High Level Output Current
Output Short Circuit Current
COMMERCIAL
I
CC
Operating Power
Supply Current
V
IL
= 0V
V
IH
= 3.0V Unused Inputs at
V
IL
—
90
130
mA
f
toggle
= 1MHz Outputs Open
1) The leakage current is due to the internal pull-up resistor on all pins. See
Input Buffer
section for more information.
2) One output at a time for a maximum duration of one second. Vout = 0.5V was selected to avoid test problems caused by tester
ground degradation. Characterized but not 100% tested.
3) Typical values are at Vcc = 3.3V and T
A
= 25
°C
6