General Specifications Genesys™ 750W/1500W
2.1 INPUT CHARACTERISTICS
1. Input voltage/freq. (*1)
2. Power Factor
3. EN61000-3-2,3 compliance
4. Input current 100/200Vac
5. Inrush current 100/200Vac
6. Hold-up time
2.2 POWER SUPPLY CONFIGURATION
1. Parallel Operation
2. Series Operation
2.3 ENVIRONMENTAL CONDITIONS
1. Operating temp
2. Storage temp
3. Operating humidity
4. Storage humidity
5. Vibration
6. Shock
7. Altitude
2.4 EMC
1.Applicable standards:
2.ESD
3.Fast transients
4.Surge immunity
5.Conducted immunity
6.Radiated immunity
7.Conducted emission
8.Radiated emission
9.Voltage dips
10. Conducted emission
11. Radiated emission
2.5 SAFETY
1.Applicable standards:
85~265Vac continuous, 47~63Hz, single phase
0.99 @100/200Vac, rated output power.
Complies with EN61000-3-2 class A and EN61000-3-3 at 20~100% output power.
750W
:10.5A / 5A,
1500W
:21A / 11A
750W
:Less than 25A,
1500W
:Less than 50A
More than 20mS , 100Vac , at 100% load.
Up to 4 units in master/slave mode with single wire current balance connection
Up to 2 units. with external diodes.
600V Max to Chassis ground
0~50
°C,
100% load.
-20~70°C
30~90% RH (no condensation).
10~95% RH (no condensation).
MIL-810E, method 514.4 , test cond. I-3.3.1 . The EUT is fixed to the vibrating surface.
Less than 20G , half sine , 11mSec. Unit is unpacked.
Operating: 10000ft (3000m) , Non operating: 40000ft (12000m).
EN55024
IEC1000-4-2. Air-disch.-8KV, contact disch.-4KV
IEC1000-4-4. 2KV
IEC1000-4-5. 1KV line to line, 2KV line to ground
IEC1000-4-6, 3V
IEC1000-4-3, 3V/m
EN55022B,FCC part 15J-B,VCCI-2
EN55022A,FCC part 15-A,VCCI-1
EN61000-4-11
EN55022B, FCC part 15-B, VCCI-2.
EN55022A, FCC part 15-A, VCCI-1.
2.Withstand voltage
3.Insulation resistance
2.6 MECHANICAL CONSTRUCTION
1. Cooling
2. Dimensions (WxHxD)
3. Weight
4. AC Input connector
5.Output connectors
2.7 RELIABILITY SPECS
1. Warranty
CE Mark, UL60950,EN60950 listed.
Vout<60V:Output is SELV , IEEE/Isolated analog are SELV.
60<Vout<400V: Output is hazardous, IEEE/Isolated analog are SELV.
400<Vout<600V:Output is hazardous, IEEE/Isolated analog are not SELV.
Vout<60V models :Input-Outputs (SELV): 3.0KVrms 1min, Input-Ground: 2.0KVrms 1min.
60<Vout<600V models: Input-Haz. Output: 2.5KVrms 1min, Input-SELV: 3KVrms 1min.
Hazardous Output.-SELV: 1.9KVrms 1min, Hazardous Output-Ground:1.9KVrms 1min.
Input-Ground: 2KVrms 1min.
More than 100Mohm at 25°C , 70% RH.
Forced air flow: from front to rear. No ventilation holes at the top or bottom of the chassis Variable fan speed.
W: 422.8mm, H: 43.6mm, D: 432.8mm (excluding connectors, encoders, handles etc..)
750W:
7Kg (15.4 Lbs)
1500W:
8.5Kg (18.7 Lbs)
750W: AC Inlet IEC320.
1500W: screw terminal block, Phoenix P/N: FRONT-4-H-7.62 , with strain relief
6V to 60V models: bus-bars (hole Ø 8.5mm).
80V to 600V models :terminal block ,Phoenix P/N: FRONT-4-H-7.62
5 years.
*1: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240Vac (50/60Hz).
Outline Drawing Genesys™ 750W/1500W Units
NOTE
1. PLUG CONNECTORS INCLUDED WITH THE POWER SUPPLY
2. CHASSIS SLIDES MOUNTING HOLES #10-32 MARKED "A"
GENERAL DEVICES
P/N: CC301-00-S160 OR EQUIVALENT
|4
LAMBDA [ DENSEI-LAMBDA ]
