欢迎访问ic37.com |
会员登录 免费注册
发布采购

CX2520SB24000D0PESZZ 参数 Datasheet PDF下载

CX2520SB24000D0PESZZ图片预览
型号: CX2520SB24000D0PESZZ
PDF下载: 下载PDF文件 查看货源
内容描述: 晶体单元表面贴装型 [Crystal Units Surface Mount Type]
分类和应用: 晶体谐振器驱动
文件页数/大小: 27 页 / 1671 K
品牌: KYOCERA AVX [ KYOCERA AVX ]
 浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第19页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第20页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第21页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第22页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第23页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第25页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第26页浏览型号CX2520SB24000D0PESZZ的Datasheet PDF文件第27页  
Handling Notes  
(5) Method of checking oscillation circuit  
Some ICs have a low upper-limit value of usable frequency, so refer to individual IC catalog to make sure that the IC can  
oscillate a crystal unit with an adequate negative resistance.  
The following figure shows an example of a CMOS oscillation circuit. Check resistance Rsup is connected in series with  
the crystal unit to check the negative resistance. Use 3 to 22pF for C1 and C2, and see the table below for values of check  
resistance.  
R
f
Frequency range  
Values of check resistance  
3.5 to 4.5MHz  
4.6 to 6.0MHz  
1.5k  
1.0k  
800  
500  
400  
R
sup  
6.1 to 10.0MHz  
10.1 to 14.0MHz  
14.1 to 20.0MHz  
C
1
C
2
Using a spectrum analyzer or oscilloscope, check that every oscillation is normally activated while turning the power on  
and off several times. For oscillation circuits with no power regulator ICs, carefully check changes in the negative  
resistance against supply voltage and in frequencies.  
When oscillation is normal, remove the check resistance before using the crystal circuit.  
If oscillation is unstable or is not generated, gradually decrease the values of C1 and C2 until normal oscillation is obtained.  
If normal oscillation cannot be generated near 10MHz or near 20MHz, replace the IC with a new one suitable for higher  
frequencies.  
(6) Load capacitance and oscillation frequency of transistor/fundamental crystal oscillation circuit  
Viewed from the connection terminals of a crystal unit, the load capacitance CL of an oscillation circuit is generally comprised  
of C1, Ct, C2, and C3 if stray capacitance of the circuit and the capacitance between base and emitter of the transistor are  
ignored. Since trimmer capacitor is adjusted to CT = MIN. to MAX. for zero adjustment of the oscillation frequency, the value  
of CL at this time can be obtained from the following equation.  
1  
1 to CLMAX.  
1
1
C2  
1
C3  
1
1
C2  
1
C3  
CLMIN.   
C1CT  
C1CT  
When these calculation results are substituted for the following equation for load resonance frequency, the oscillation  
frequency can be obtained.  
C1  
fL fs  
1  
2 (C0CL)  
- 57 -  
 复制成功!