28 | Keysight | Infiniium 90000 Series Oscilloscopes - Data Sheet
Infiniium 90000A Series Oscilloscopes (Continued)
Performance characteristics (Continued)
Hardware trigger
Sensitivity 2
91304A/91204A/90804A:
Internal low 2:
Internal high 2:
2.0 div p-p 0 to 5 GHz
0.3 div p-p 0 to 4 GHz, 1.0 div p-p 4 to 7.5 GHz
2.0 div p-p 0 to 5 GHz
0.3 div p-p 0 to 3 GHz, 1.0 div p-p 3 to 5 GHz
DC to 100 MHz: 200 mV p-p into 50 Ω
100 MHz to 1 GHz: 500 mV p-p into 50 Ω
90604A/90404A/90254A 12: Internal low 2:
Internal high 2:
Auxiliary:
Level range
Internal
Auxiliary
± 4 div from center screen or ± 4 Volts, whichever is smallest
± 5 V, also limit input signal to ± 5 V
Auto, triggered, single
Sweep modes
Display jitter (trigger jitter) 2, 3, 4
Trigger sources
Trigger modes
Edge
620 fs rms
Channel 1, channel 2, channel 3, channel 4, aux, and line
Triggers on a specified slope (rising, falling or alternating between rising and falling) and voltage level on any channel
or auxiliary trigger.
Edge transition
Edge then edge (time)
Edge then edge (event)
Glitch
Trigger on rising or falling edges that cross two voltage levels in > or < the amount of time specified. Edge transition
setting from 250 ps.
The trigger is qualified by an edge. After a specified time delay between 10 ns to 10 s, a rising or falling edge on any
one selected input will generate the trigger.
The trigger is qualified by an edge. After a specified delay between 1 to 16,000,000 rising or falling edges, another
rising or falling edge on any one selected input will generate the trigger.
Triggers on glitches narrower than the other pulses in your waveform by specifying a width less than your narrowest
pulse and a polarity. Triggers on glitches as narrow as 125 ps. Glitch range settings: < 250 ps to < 10 s.
Line
Triggers on the line voltage powering the oscilloscope.
Pulse width
Trigger on a pulse that is wider or narrower than the other pulses in your waveform by specifying a pulse width and a
polarity. Triggers on pulse widths as narrow as 125 ps. Pulse width range settings: 250 ps to 10 s. Trigger point can
be “end of pulse” or “time out”.
Runt
Triggers on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.
Can be time qualified with minimum setting of 250 ps.
Timeout
Trigger when a channel stays high, low, or unchanged for too long. Timeout setting: from 250 ps to 10 s.
Pattern/pulse range
Triggers when a specified logical combination of the channels is entered, exited, present for a specified period of time
or is within a specified time range or times out. Each channel can have a value of High (H), Low (L) or Don’t care (X).
State
Pattern trigger clocked by the rising, falling or alternating between rising and falling edge of one channel.
Setup/hold
Triggers on setup, hold, or setup and hold violations in your circuit. Requires a clock and data signal on any two inputs
(except aux or line) channels as trigger sources. Setup and/or hold time must then be specified.
1� Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 5 °C from firmware calibration
temperature�
2� Internal edge trigger mode with JitterFree correction� Value depends on scope settings and trigger signal characteristics, and is equal to TIE value
expressed in the formula above using the minimum time scale accuracy value�
3� Value shown represents typical Display jitter for 91204A at 100 mV/div triggering on 500 mVpp 6 GHz sin wave signal�
4� Sample rate at maximum� Noise and slew rate determined at fixed-voltage trigger threshold, near middle of signal� Displayed signal not vertically clipped�