CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Radial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Ceramic Capacitors for automatic
insertion per EIA specification RS-468. Parts are taped to a
tagboard carrier strip, and wound on a reel as shown in
Figure 1. Kraft paper interleaving is inserted between the
layers of capacitors on the reel. Ammopack is also available,
with the same lead tape configuration and package quantities.
Figure 1
®
Carrier Strip
KEMET
12"
(30.48 cm)
*
.059" to .315"
Greater Than
Over All
Height
of Taped
Components
KEMET
Adhesive Tape
®
Hub
.655"
±0.010"
(16.6
±0.25)
3
1
/
4
"
(82.6)
1/ "
8
(3.18)
Carrier Tape
Kraft Paper
Interleaving
Figure 3: Standard Reel
C315*
C320*
C330**
C340**
C6xx#
C056**
C066**
(Note: Non-standard lead lengths
available in bulk only.)
CK06**
CKR06**
C062**
CK05**
CKR05**
C052**
P
C317**
C322**
C323**
C6xx#
C333**
∆H
P
2
H
1
D
0
P1
1MM Max.
(.039")
H
H
0
W
2
W
0
L
1
W
Tape
W
2
Carrier
F
T
Figure 2: Lead Tape Configuration (See Table Below)
P
0
* Lead spacings are 2.54mm
(.10") center-to-center.
** Lead spacings are 5.08mm
(.20") center-to-center.
# See page 15 for exact lead
configuration for Series.
Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)
Dimension
Sprocket Hole Diameter
Sprocket Hole Pitch
Component Pitch
Lead Spacing (1)
Sprocket Hole Center
to Lead Center (1)
Sprocket Hole Center
to Component Center
Height to Seating Plane
(straight leads) (2)
Component Height
Above Tape Center
Symbol
Do
P0
P
F
P1
P2
H
H1
Nominal
mm (inch)
4.0 (.157)
12.7 (.500)
12.7 (.500)
5.08
2.54
(.20)
(.10)
3.81
5.08
(.150)
(.200)
6.35 (.250)
Tolerance
mm (inch)
±
0.2 (.008)
±
0.3 (.012)
±
0.3 (.012)
+0.6 -0.2
(+.024 -.008)
±
0.7 (.028)
±
1.3 (.051)
Nominal
Tolerance
Dimension
Symbol
mm (inch)
mm (inch)
H
0
Height to Seating
7301
7303
7301
7303
Plane (formed leads) (2)
16.0 (.630) 18.0 (.709)
±0.5
(.020) Minimum
Component Alignment
∆h
4.0 (.157)
±0.2
(.008)
Lead Protrusion
Composite Tape
Thickness
Overall Tape and
Lead Thickness
Carrier Tape Width
Hold-Down Tape
Width
Hold-Down Tape
Location
L1
t
T
W
W0
W2
1.0 (.039)
0.7 (.051)
1.5 (.059)
18.0 (.709)
5.0 (.197)
3.0 (.118)
Maximum
±0.2
(.008)
Maximum
+1.0 - 0.5
(+.039 -.020)
Minimum
Maximum
7301
7303
7301
7303
16.0 (.630) 18.0 (.709)
±0.5
(.020) Minimum
32.2 (1.27)
Maximum
(1) Measured at the egress from the carrier tape, on the component side.
(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:
7301 = Recommended for parts with formed leads.
Example: C322C104K5R5CA7301
7303 = Recommended for parts with straight leads.
Example: C320C104K5R5CA7303
40
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
KEMET [ KEMET CORPORATION ]
