KEMET®
CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Radial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Ceramic Capacitors for automatic
insertion per EIA specification RS-468. Parts are taped to a
tagboard carrier strip, and wound on a reel as shown in
Figure 1. Kraft paper interleaving is inserted between the
layers of capacitors on the reel. Ammopack is also available,
with the same lead tape configuration and package quantities.
Figure 1
®
KEMET
Carrier Strip
12"
(30.48 cm)
.059" to .315"
Greater Than
Over All
*
Height
®
of Taped
KEMET
Components
Adhesive Tape
Hub
1
Kraft Paper
Interleaving
Carrier Tape
3 / "
4
(82.6)
.655" ±0.010"
(16.6 ±0.25)
1
/ "
8
(3.18)
Figure 3: Standard Reel
CK06**
CK05**
C317**
C322**
C323**
C315*
C320*
C330**
C340**
C056**
C066**
CKR06** CKR05**
C062**
C052**
C333**
∆H
P
2
P
1MM Max.
(.039")
H1
D0
P1
W
2
H
F
H0
W
W
0
Tape
Carrier
W
2
L
1
T
* Lead spacings are 2.54mm
(.10") center-to-center.
** Lead spacings are 5.08mm
(.20") center-to-center.
P
0
Figure 2: Lead Tape Configuration (See Table Below)
Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)
Nominal
mm (inch)
Tolerance
mm (inch)
Nominal
mm (inch)
Tolerance
mm (inch)
Dimension
Symbol
Dimension
Symbol
Sprocket Hole Diameter
Do
4.0 (.157)
12.7 (.500)
12.7 (.500)
± 0.2 (.008)
± 0.3 (.012)
± 0.3 (.012)
Height to Seating
Plane (formed leads) (2)
Component Alignment
H0
C7301 C7303
16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum
C7301 C7303
Sprocket Hole Pitch
Component Pitch
Lead Spacing (1)
P0
P
∆h
L1
t
4.0 (.157)
1.0 (.039)
0.7 (.051)
1.5 (.059)
18.0 (.709)
5.0 (.197)
3.0 (.118)
±0.2 (.008)
Maximum
±0.2 (.008)
Maximum
Lead Protrusion
Composite Tape
Thickness
Overall Tape and
Lead Thickness
Carrier Tape Width
F
5.08
(.20)
3.81
2.54
(.10)
5.08
+0.6 -0.2
(+.024 -.008)
± 0.7 (.028)
Sprocket Hole Center
to Lead Center (1)
Sprocket Hole Center
to Component Center
Height to Seating Plane
(straight leads) (2)
P1
P2
H
T
(.150)
(.200)
6.35 (.250)
± 1.3 (.051)
W
W0
W2
+1.0 - 0.5
(+.039 -.020)
Minimum
Hold-Down Tape
Width
Hold-Down Tape
Location
C7301
C7303
C7301
C7303
16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum
32.2 (1.27) Maximum
Component Height
Above Tape Center
H1
Maximum
(1) Measured at the egress from the carrier tape, on the component side.
(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:
7301 =
7303 =
Recommended for parts with formed leads.
Recommended for parts with straight leads.
Example: C322C104K5R5CA7301
Example: C320C104K5R5CA7303
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
33
KEMET [ KEMET CORPORATION ]
