Micro-D Metal Shell - .050" Contact Spacing
Panel Cutouts
NOTE: See page 13 for rear panel mounting configuration.
Shell Sizes 9 thru 51
.450±.002
(11.43±0.05)
C
.030 (0.76) TYP.
MDM
C
D
TYP.
C
D
TYP.
A
.100
+.005
-.000
(2.54)
+0.13
)
R TYP.
-0.00
D
B
+ +
+ +
B
.015 (0.38)R.
MAX.(TYP)
FULL R. (TYP.)
FULL R.
(TYP.)
A
26˚/27˚TYP
FULL R.
(TYP.)
PANEL REF.
Figure 1
Front Mounting
Figure 2
Rear Mounting
Figure 3
Edgeboard Mounting
Shell Size 100
.450+_.002
.118
+.005
-.000
-0.00
1.805
+.005
-.000
-0.00
(3.00
+0.13
)
(45.85
+0.13
)
.361
+.004
-.000
+.005
-.000
(3.00
+0.13
)
-0.00
.118
+.005
-.000
(45.85
+0.13
)
-0.00
(11.43+_0.05)
.030
(0.76) TYP.
1.805
+.005
-.000
(45.85
+0.13
)
-0.00
1.805
+.005
-.000
(3.00
+0.13
)
-0.00
.118
.401
-.000
+.004
(9.17
+0.10
)
-0.00
1.456
.015 (0.38)
R. MAX (TYP.)
+.004
-.000
(10.18
+0.10
)
-0.00
+ +
+ +
(36.98
+0.10
)
-0.00
FULL R. (TYP.)
1.520
-.000
.125
(3.18
)
+.004
(38.61
+0.10
)
-0.00
FULL R. (TYP.)
FULL R. (TYP.)
PANEL REF.
Figure 1
Front Mounting
Figure 2
Rear Mounting
Figure 3
Edgeboard Mounting
For 9-51 Shell Sizes
NOTES:
1. Front panel mounting is the preferred mounting
method. Front panel mounting dimensions
(figure 1) will accommodate either #2-56 screws
or jackpost hardware.
2. Rear panel mount dimensions (figure 2) will
accommodate #2-56 screw hardware only.
When mounting the connector with rear panel
mount jackpost see the panel cut-out
dimensions.
3. Edgeboard mounting bracket (figure 3) uses #2-
56 screws. Dimension .450+/-.002 (11.43+/-
0.05) locates the MDM receptacle flush with the
end of the board.
For 100 Shell Size
NOTES:
1. Front mounting is the preferred mounting
method. Front panel mounting dimensions
(figure 1) will accommodate either #4-40 screws
or jackpost hardware.
2. Rear panel mount dimensions (figure 2) will
accommodate #4-40 screw hardware only see
the panel cut-out dimensions.
3.Edgeboard mounting bracket (figure 3) uses #4-
40 screws. Dimension .450+/-.002 (11.43+/-
0.05) locates the MDM receptacle flush with the
end of the board.
Shell
Size
9
Cutout
Figure
1
2
3
1
A
+.004
-.000
.408
.401
-
.558
.551
-
.708
.701
-
.808
.801
-
.958
.951
-
1.108
1.101
-
1.058
1.051
-
B
+.004
-.000
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.315
.295
C
+.005
-.000
.570
.570
.570
.720
.720
.720
.870
.870
.870
.970
.970
.970
1.120
1.120
1.120
1.270
1.270
1.270
1.220
1.220
1.220
D
+.005
-.000
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
15
2
3
1
21
2
3
1
25
2
3
1
31
2
3
1
37
2
3
1
51
2
3
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
11
ITT [ ITT INDUSTRIES ]
