AS7C33256PFD32A
AS7C33256PFD36A
®
Functional description
The AS7C33256PFD32A and AS7C33256PFD36A are high-performance CMOS 8-Mbit Synchronous Static Random Access
Memory (SRAM) devices organized as 262,144 words x 32 or 36 bits, and incorporate a two-stage register-register pipeline
for highest frequency on any given technology.
Fast cycle times of 6/7.5 ns with clock access times (t ) of 3.5/4.0 ns enable 166 and 133 MHz bus frequencies. Two-chip
CD
enable and three-chip enable (CE) inputs permit versatility and easy memory expansion. Burst operation is initiated in one of
two ways: the controller address strobe (ADSC), or the processor address strobe (ADSP). The burst advance pin (ADV)
allows subsequent internally generated burst addresses.
Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip
address register when ADSP is sampled LOW, the chip enables are sampled active, and the output buffer is enabled with OE.
In a read operation the data accessed by the current address, registered in the address registers by the positive edge of CLK, are
carried to the data-out registers and driven on the output pins on the next positive edge of CLK. ADV is ignored on the clock
edge that samples ADSP asserted, but is sampled on all subsequent clock edges. Address is incremented internally for the next
access of the burst when ADV is sampled LOW, and both address strobes are HIGH. Burst mode is selectable with the LBO
input. With LBO unconnected or driven HIGH, burst operations use an interleaved count sequence. With LBO driven LOW, the
device uses a linear count sequence.
Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable
GWE writes all 32/36 bits regardless of the state of individual BW[a:d] inputs. Alternately, when GWE is HIGH, one or more
bytes may be written by asserting BWE and the appropriate individual byte BWn signal(s).
BWn is ignored on the clock edge that samples ADSP LOW, but is sampled on all subsequent clock edges. Output buffers are
disabled when BWn is sampled LOW (regardless of OE). Data is clocked into the data input register when BWn is sampled
LOW. Address is incremented internally to the next burst address if BWn and ADV are sampled LOW. This device operates in
double cycle deselect features during real cycle.
Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC
and ADSP are as follows:
• ADSP must be sampled HIGH when ADSC is sampled LOW to initiate a cycle with ADSC.
• WE signals are sampled on the clock edge that samples ADSC LOW (and ADSP HIGH).
• Master chip enable CE0 blocks ADSP, but not ADSC.
AS7C33256PFD32A and AS7C33256PFD36A family operates from a core 3.3V power supply. I/Os use a separate power
supply that can operate at 2.5V or 3.3V. These devices are available in a 100-pin 14 × 20 mm TQFP package.
TQFP thermal Capacitance
Parameter
Input capacitance
I/O capacitance
Symbol
Test conditions
= 0V
Min
Max
Unit
pF
*
C
V
-
-
5
7
IN
IN
*
C
V
= V = 0V
OUT
pF
I/O
IN
*
Guaranteed not tested
TQFP thermal resistance
Description
Conditions
Symbol
Typical
40
Units
°C/W
°C/W
1–layer
4–layer
θJA
θJA
Thermal resistance
(junction to ambient)1
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA/JESD51
22
Thermal resistance
(junction to top of case)1
θJC
8
°C/W
1 This parameter is sampled
12/1/04, v.1.2
Alliance Semiconductor
P. 4 of 20
ISSI [ INTEGRATED SILICON SOLUTION, INC ]
