ISL43L110, ISL43L111
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . .
±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max)
. . . . . . . . . . . . . . . . . ±
600mA
ESD Rating:
HBM
>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>4kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1000V
Thermal Information
Thermal Resistance (Typical, Note 3)
θ
JA
(°C/W)
5 Ld SC70 Package . . . . . . . . . . . . . . . . . . . . . . . . .
660
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3.
θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, V
INH
= 1.6V, V
INL
= 0.5V (Notes 4, 6),
Unless Otherwise Specified
TEST CONDITIONS
TEMP
(°C)
(NOTE 5)
MIN
TYP
(NOTE 5)
MAX
UNITS
PARAMETER
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
ON Resistance, R
ON
Full
V+ = 3.9V, I
COM
= 100mA, V
NO
or V
NC
= 2.2V
(See Figure 4)
V+ = 3.9V, I
COM
= 100mA, V
NO
or V
NC
= 0.8V, 2.2V,
3.5V, (Note 7)
V+ = 4.5V, V
COM
= 0.3V, 3V, V
NO
or V
NC
= 3V, 0.3V
25
Full
25
Full
25
Full
V+ = 4.5V, V
COM
= 0.3V, 3V, or V
NO
or V
NC
= 0.3V, 3V,
or Floating
25
Full
0
-
-
-
-
-30
-200
-3
-35
-
0.22
0.25
0.03
0.05
-
-
-
-
V+
-
-
-
-
30
200
3
35
V
Ω
Ω
Ω
Ω
nA
nA
nA
nA
R
ON
Flatness, R
FLAT(ON)
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
COM ON Leakage Current,
I
COM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 3.9V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω, C
L
= 35pF
(See Figure 1, Note 8)
V+ = 3.9V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω, C
L
= 35pF
(See Figure 1, Note 8)
V
G
= V+/2, R
G
= 0Ω, C
L
= 1.0nF (See Figure 2)
R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
,
(See Figure 3)
f = 20Hz to 20kHz, V
COM
= 2V
P-P
, R
L
= 32Ω
25
Full
25
Full
25
25
25
25
25
-
-
-
-
-
-
-
-
-
8
-
5
-
89
-65
0.003
68
160
15
20
10
15
-
-
-
-
-
ns
ns
ns
ns
pC
dB
%
pF
pF
Turn-OFF Time, t
OFF
Charge Injection, Q
OFF Isolation
Total Harmonic Distortion
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (See Figure 5)
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (See Figure 5)
3
FN6130.0
March 15, 2005
INTERSIL [ INTERSIL CORPORATION ]
