ICM7555, ICM7556
Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
c1 LEAD FINISH
F14.3 MIL-STD-1835 GDIP1-T14 (D-1, CONFIGURATION A)
14 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE
-D-
E
-A-
INCHES MILLIMETERS
MIN
BASE
(c)
METAL
SYMBOL
MAX
0.200
0.026
0.023
0.065
0.045
0.018
0.015
0.785
0.310
MIN
-
MAX
5.08
0.66
0.58
1.65
1.14
0.46
0.38
19.94
7.87
NOTES
b1
A
b
-
-
M
M
(b)
0.014
0.014
0.045
0.023
0.008
0.008
-
0.36
0.36
1.14
0.58
0.20
0.20
-
2
-B-
b1
b2
b3
c
3
SECTION A-A
bbb
C A - B
D
D
S
S
S
-
4
BASE
PLANE
Q
2
A
-C-
SEATING
PLANE
c1
D
3
L
α
5
S1
b2
eA
A A
e
E
0.220
5.59
5
b
C A - B
eA/2
aaa M C A - B S D S
c
e
0.100 BSC
2.54 BSC
-
eA
eA/2
L
0.300 BSC
0.150 BSC
7.62 BSC
3.81 BSC
-
ccc
D
S
M
S
-
NOTES:
0.125
0.200
0.060
-
3.18
5.08
1.52
-
-
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
Q
0.015
0.38
6
S1
0.005
0.13
7
90°
105°
0.015
0.030
0.010
0.0015
90°
105°
0.38
0.76
0.25
0.038
-
α
aaa
bbb
ccc
M
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
-
-
-
-
-
-
-
-
-
-
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
-
2, 3
8
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
N
14
14
Rev. 0 4/94
5. This dimension allows for off-center lid, meniscus, and glass
overrun.
6. Dimension Q shall be measured from the seating plane to the
base plane.
7. Measure dimension S1 at all four corners.
8. N is the maximum number of terminal positions.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN2867.9
August 24, 2006
12
INTERSIL [ Intersil ]
