DG441, DG442
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
GND to V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+34V
Thermal Resistance (Typical, Note 2)
θ
(°C/W)
JA
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
115
150
Digital Inputs, V , V (Note 1)
S
D
. . . . . . . . (V-) -2V to (V+) + 2V or 30mA, Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Maximum Junction Temperature (Plastic Packages) . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(SOIC and TSSOP- Lead Tips Only)
Operating Conditions
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Signal Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±20V (Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤20ns
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S , D or IN exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
X
X
X
2. θ is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
Electrical Specifications (Dual Supply) Test Conditions: V+ = +15V, V- = -15V, V = 2.4V, 0.8V, V
= V , V ,
S D
IN
ANALOG
Unless Otherwise Specified
TEMP
(NOTE 3)
PARAMETER
TEST CONDITIONS
(°C)
MIN
TYP
MAX
UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
R
= 1kΩ, C = 35pF, V = ±10V, (Figure 1)
+25
+25
-
150
250
ns
ON
L
L
S
Turn-OFF Time, t
DG441
OFF
-
-
-
-
-
-
-
-
90
110
-1
120
ns
ns
DG442
210
Charge Injection, Q (Figure 2)
OFF Isolation (Figure 4)
C = 1nF, V = 0V, R = 0Ω
+25
+25
+25
+25
+25
+25
-
-
-
-
-
-
pC
dB
dB
pF
pF
pF
L
G
G
R
= 50Ω, C = 5pF, f = 1MHz
60
-100
4
L
L
Crosstalk (Channel-to-Channel) (Figure 3)
Source OFF Capacitance, C
f = 1MHz, V = 0 (Figure 5)
ANALOG
S(OFF)
Drain OFF Capacitance, C
4
D(OFF)
Channel ON Capacitance,
16
C
+ C
S(ON)
D(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current V Low, I
V
V
Under Test = 0.8V, All Others = 2.4V
Under Test = 2.4V, All Others = 0.8V
Full
Full
-0.5
-0.5
-0.00001
0.00001
0.5
0.5
μA
μA
IN
IL
IH
IN
IN
Input Current V High, I
IN
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
Full
+25
+85
+25
+85
+25
+85
+25
+85
-15
-
-
15
85
100
0.5
5
V
ANALOG
Drain-Source ON Resistance, r
)
I
=
10mA, V = ±8.5V, V+ = 13.5V,
50
Ω
DS(ON
S
D
V- = -13.5V
-
-
Ω
Source OFF Leakage Current, I
V+ = 16.5V, V- = -16.5V, V = ±15.5V,
V
-0.5
-5
0.01
nA
nA
nA
nA
nA
nA
S(OFF)
D(OFF)
D
=
15.5V
S
-
0.01
-
Drain OFF Leakage Current, I
-0.5
-5
0.5
5
Channel ON Leakage Current,
+ I
V+ = 16.5V, V- = -16.5V, V = V = ±15.5V
-0.5
-10
0.08
-
0.5
10
S
D
I
D(ON)
S(ON)
FN3281.10
November 20, 2006
4
INTERSIL [ Intersil ]
