DG201A, DG202
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
V
IN
to Ground (Note 1) . . . . . . . . . . . . . . . . . . . (V-) -2V to (V+) +2V
V
S
or V
D
to V+ (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . +2 to (V-) -2V
V
S
or V
D
to V- (Note 1) . . . . . . . . . . . . . . . . . . . . . . . -2 to (V+) +2V
Current, any Terminal Except S or D . . . . . . . . . . . . . . . . . . . . 30mA
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 70mA
Thermal Information
Thermal Resistance (Typical, Note 2)
θ
JA
(
o
C/W)
θ
JC
(
o
C/W)
CERDIP Package. . . . . . . . . . . . . . . . .
75
20
PDIP Package . . . . . . . . . . . . . . . . . . .
100
N/A
SOIC Package . . . . . . . . . . . . . . . . . . .
100
N/A
Maximum Junction Temperature
Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
o
C
Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
o
C
Maximum Storage Temperature Range . . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300
o
C
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range
“A” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
“B” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25
o
C to 85
o
C
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 70
o
C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on V
S
, V
D
, or V
IN
exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V+ = 15V, V- = -15V, GND = 0V, T
A
= 25
o
C
“A” SUFFIX
“B” AND “C” SUFFIX
MAX
MIN
(NOTE 3)
TYP
MAX
UNITS
PARAMETER
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
Turn-OFF Time, t
OFF
Charge Injection, Q
OFF Isolation, OIRR
Crosstalk (Channel to Channel), CCRR
Source OFF Capacitance, C
S(OFF)
Drain OFF Capacitance, C
D(OFF)
Channel ON Capacitance,
C
D(ON)
+ C
S(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current with Voltage High, I
IH
TEST CONDITIONS
MIN
(NOTE 3)
TYP
See Figure 1
See Figure 1
C
L
= 1nF, R
S
= 0, V
S
= 0V
V
IN
= 5V, R
L
= 75Ω, V
S
= 2.0V,
f = 100kHz
f = 140kHz, V
IN
= 5V, V
S
= V
D
= 0V
-
-
-
-
-
-
-
-
480
370
20
70
-90
5.0
5.0
16
600
450
-
-
-
-
-
-
-
-
-
-
-
-
-
-
480
370
20
70
-90
5.0
5.0
16
-
-
-
-
-
-
-
-
ns
ns
pC
dB
dB
pF
pF
pF
V
IN
= 2.4V
V
IN
= 15V
-1.0
-
-1.0
-0.0004
0.003
-0.0004
-
1.0
-
-1.0
-
-1.0
-0.0004
0.003
-0.0004
-
1.0
-
µA
µA
µA
Input Current with Voltage Low, I
IL
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Drain-Source ON Resistance, r
DS(ON)
Source OFF Leakage Current, I
S(OFF)
V
IN
= 0V
-15
V
D
=
±10V,
V
IN
= 0.8V (DG201A)
I
S
= 1mA, V
IN
= 2.4V (DG202)
V
IN
= 2.4V
(DG201A)
V
IN
= 0.8V
(DG202)
V
S
= 14V, V
D
= -14V
V
S
= -14V, V
D
= 14V
V
S
= -14V, V
D
= 14V
V
S
= 14V, V
D
= -14V
-
-
-1.0
-
-1.0
-
115
0.01
-0.02
0.01
-0.02
15
175
1.0
-
1.0
-
-15
-
-
-5.0
-
-5.0
-
115
0.01
-0.02
0.01
-0.02
15
200
5.0
-
5.0
-
V
Ω
nA
nA
nA
nA
Drain OFF Leakage Current, I
D(OFF)
4-2
INTERSIL [ INTERSIL CORPORATION ]
