80C186EC 188EC 80L186EC 188EC
pulled low for four clock cycles Logically ANDing
the WDTOUT pin with the power-on reset signal al-
lows the WDT to reset the device in the event of a
WDT timeout If a less drastic method of recovery is
desired WDTOUT can be connected directly to NMI
or one of the INT input pins The WDT may also be
used as a general purpose timer
and information see the Intel Packaging Outlines
and Dimensions Guide (Order Number 231369)
Prefix Identification
Table 1 lists the prefix identifications
Table 1 Prefix Identification
Prefix Note
TS
KU
SB
S
1
1
1
Package
Type
PQFP
SQFP
Temperature
Range
Extended Commercial
Extended Commercial
Power Management Unit
The 80C186EC Power Management Unit (PMU) is
provided to control the power consumption of the
device The PMU provides four power management
modes Active Powersave Idle and Powerdown
Active Mode indicates that all units on the
80C186EC are operating at
the CLKIN frequency
Idle Mode freezes the clocks of the Execution and
Bus units at a logic zero state (all peripherals contin-
ue to operate normally)
The Powerdown Mode freezes all internal clocks at
a logic zero level and disables the crystal oscillator
In Powersave Mode all internal clock signals are di-
vided by a programmable prescalar (up to
the
normal frequency) Powersave Mode can be used
with Idle Mode as well as during normal (Active
Mode) operation
QFP (EIAJ) Extended
QFP (EIAJ) Commercial
NOTE
1 The 5V 25 MHz version is only available in commercial
temperature range corresponding to 0 C to
a
70 C am-
bient
Pin Descriptions
Each pin or logical set of pins is described in Table
2 There are four columns for each entry in the Pin
Description Table The following sections describe
each column
Column 1 Pin Name
In this column is a mnemonic that de-
scribes the pin function Negation of the
signal name (i e RESIN) implies that the
signal is active low
Column 2 Pin Type
A pin may be either power (P) ground
(G) input only (I) output only (O) or in-
put output (I O) Please note that some
pins have more than 1 function
A19 S6 ONCE for example is normally
an output but functions as an input dur-
ing
reset
For
this
reason
A19 S6 ONCE is classified as an input
output pin
Column 3 Input Type (for I and I O types only)
There are two different types of input
pins on the 80C186EC asynchronous
and synchronous
Asynchronous
pins
require that setup and hold times be met
only to
guarantee recognition
Synchro-
nous
input pins require that the setup
and hold times be met to
guarantee
proper operation
Stated simply missing
a setup or hold on an asynchronous pin
will result in something minor (i e a timer
count will be missed) whereas missing a
setup or hold on a synchronous pin will
result in system failure (the system will
‘‘lock up’’)
An input pin may also be edge or level
sensitive
80C187 Interface (80C186EC only)
The 80C186EC supports the direct connection of
the 80C187 Numerics Processor Extension The
80C187 can dramatically improve the performance
of calculation intensive applications
ONCE Test Mode
To facilitate testing and inspection of devices when
fixed into a target system the 80C186EC has a test
mode available which forces all output and input
output pins to be placed in the high-impedance
state ONCE stands for ‘‘ON Circuit Emulation’’
The ONCE mode is selected by forcing the
A19 S6 ONCE pin low during a processor reset
(this pin is weakly held high during reset to prevent
inadvertant entrance into ONCE Mode)
PACKAGE INFORMATION
This section describes the pin functions pinout and
thermal characteristics for the 80C186EC in the
Plastic Quad Flat Pack (JEDEC PQFP) the EIAJ
Quad Flat Pack (QFP) and the Shrink Quad Flat
Pack (SQFP) For complete package specifications
8
INTEL [ INTEL CORPORATION ]
