欢迎访问ic37.com |
会员登录 免费注册
发布采购

550 参数 Datasheet PDF下载

550图片预览
型号: 550
PDF下载: 下载PDF文件 查看货源
内容描述: 奔腾4处理器,支持超线程技术 [Pentium 4 Processors Supporting Hyper-Threading Technology]
分类和应用:
文件页数/大小: 96 页 / 1585 K
品牌: INTEL [ INTEL ]
 浏览型号550的Datasheet PDF文件第22页浏览型号550的Datasheet PDF文件第23页浏览型号550的Datasheet PDF文件第24页浏览型号550的Datasheet PDF文件第25页浏览型号550的Datasheet PDF文件第27页浏览型号550的Datasheet PDF文件第28页浏览型号550的Datasheet PDF文件第29页浏览型号550的Datasheet PDF文件第30页  
Electrical Specifications  
Table 2-8. Voltage and Current Specifications (Sheet 2 of 2)  
Symbol  
ICC_VCCA  
Parameter  
Min  
Typ  
Max  
Unit  
Notes1  
15  
ICC FOR PLL LANDS  
ICC FOR I/O PLL LAND  
ICC for GTLREF  
120  
100  
200  
mA  
mA  
µA  
15  
15  
ICC_VCCIOPLL  
ICC_GTLREF  
NOTES:  
1.  
Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data. These specifications will be up-  
dated with characterized data from silicon measurements at a later date.  
2.  
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at manufacturing and can not be altered.  
Individual maximum VID values are calibrated during manufacturing such that two processors at the same frequency may have different settings  
within the VID range. Note this differs from the VID employed by the processor during a power management event (Thermal Monitor 2 or En-  
hanced HALT State).  
3.  
4.  
These voltages are targets only. A variable voltage source should exist on systems in the event that a different voltage is required. See Section 2.4  
and Table 2-2 for more information.  
The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE lands at the socket with a 100 MHz bandwidth os-  
cilloscope, 1.5 pF maximum probe capacitance, and 1 Mminimum impedance. The maximum length of ground wire on the probe should be less  
than 5 mm. Ensure external noise from the system is not coupled into the oscilloscope probe.  
5.  
6.  
7.  
8.  
9.  
Refer to Table 2-10 and Figure 2-3 for the minimum, typical, and maximum V allowed for a given current. The processor should not be sub-  
CC  
jected to any Vcc and Icc combination wherein V exceeds V  
for a given current.  
cc_max  
CC  
775_VR_CONFIG_04A and 775_VR_CONFIG_04B refer to voltage regulator configurations that are defined in the Voltage Regulator Down  
(VRD) 10.1 Design Guide For Desktop LGA775 Socket.  
Refer to Table 2-9 and Figure 2-2 for the minimum, typical, and maximum V allowed for a given current. The processor should not be subjected  
CC  
to any V and I combination wherein V exceeds V for a given current.  
CC  
CC  
CC  
CC_max  
These frequencies will operate in a system designed for 775_VR_CONFIG_04B processors. The power and I will be incrementally higher in  
CC  
this configuration due to the improved loadline and resulting higher V  
.
CC  
I
is specified at V  
.
cc_max  
CC_max  
10. The current specified is also for AutoHALT State.  
11. Icc Stop-Grant and I Enhanced Auto Halt are specified at V  
.
CC  
CC_max  
12. The maximum instantaneous current the processor will draw while the thermal control circuit is active as indicated by the assertion of PROCHOT#  
is the same as the maximum Icc for the processor.  
13.  
V
must be provided via a separate voltage source and not be connected to V . This specification is measured at the land.  
TT CC  
14. Baseboard bandwidth is limited to 20 MHz.  
15. These parameters are based on design characterization and are not tested.  
16. This is maximum total current drawn from V plane by only the processor. This specification does not include the current coming from R  
TT  
TT  
TT  
(through the signal line). Refer to the Voltage Regulator Down (VRD) 10.1 Design Guide For Desktop LGA775 Socket to determine the total I  
drawn by the system.  
26  
Datasheet  
 复制成功!