Electrical Specifications
Table 2-10. Voltage and Current Specifications (Sheet 2 of 2)
Notes
Symbol
Parameter
Min
Typ
Max
Unit
1,13
I
I
I
I
for Dual-Core Intel Xeon
CC_RESET
150
A
18
CC_RESET
Processor 5000 series with multiple
VID (1066 MHz)
I
for Dual-Core Intel Xeon
CC_RESET
115
6.1
A
A
18
16
CC_RESET
TT
Processor 5063 (MV) with multiple
VID
Steady-state FSB Termination
Current
I
I
Power-up FSB Termination Current
8.0
A
A
19
TT_POWER-UP
CC_TDC
Thermal Design Current (TDC) for
Dual-Core Intel Xeon Processor
5000 series (667 MHz)
100
6,15
I
I
I
Thermal Design Current (TDC) for
Dual-Core Intel Xeon Processor
5000 series (1066 MHz)
130
100
580
A
A
6,15
6,15
17
CC_TDC
Thermal Design Current (TDC) for
Dual-Core Intel Xeon Processor
5063 (MV)
CC_TDC
DC current that may be drawn
mA
CC_VTTOUT
from V
per land
TTOUT
I
I
I
I
I
I
I
I
for PLL power lands
for PLL power lands
for GTLREF
120
100
200
150
mA
mA
µA
A
8
8
9
CC_VCCA
CC_VCCIOPLL
CC_GTLREF
TCC
CC
CC
CC
CC
during active thermal control
circuit (TCC) for Dual-Core Intel
Xeon Processor 5000 series
I
I
I
I
I
during active thermal control
CC
115
50
A
A
A
A
TCC
circuit (TCC) for Dual-Core Intel
Xeon Processor 5063 (MV)
I
Stop-Grant for Dual-Core Intel
CC
7
7
7
SGNT
SGNT
SGNT
Xeon Processor 5000 series (667
MHz)
I
Stop-Grant for Dual-Core Intel
60
CC
Xeon Processor 5000 series (1066
MHz)
I
Stop-Grant for Dual-Core Intel
40
CC
Xeon Processor 5063 (MV)
Notes:
1.
2.
3.
Unless otherwise noted, all specifications in this table apply to all processors and are based on final silicon
validation/characterization.
These voltages are targets only. A variable voltage source should exist on systems in the event that a
different voltage is required. See Section 2.5 for more information.
The voltage specification requirements are measured across the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands with a 100 MHz bandwidth
oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The maximum length of
ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled
in the scope probe.
4.
5.
The processor must not be subjected to any static V level that exceeds the V
associated with any
CC
CC_MAX
particular current. Failure to adhere to this specification can shorten processor lifetime.
is specified at V . The processor is capable of drawing I for up to 10 ms. Refer to
I
CC_MAX
CC_MAX
CC_MAX
Figure 2-2 and Figure 2-3 for further details on the average processor current draw over various time
durations.
6.
7.
8.
9.
10.
26
Dual-Core Intel® Xeon® Processor 5000 Series Datasheet
INTEL [ INTEL ]
