TC39x BC/BD-Step
HistoryChanges from Version 1.1 to Version 1.2
–
–
Typos corrected in footnotes for sub-chapter “Absolute Maximum Ratings”
Typo corrected for parameter IINSA in table “Overload Parameters” of sub-chapter “Pin Reliability in
Overload”
–
–
–
–
–
–
–
–
Changed values for parameter GETH frequency in table “Operating Conditions”
Changed note for parameter tTX_ASYM in table “Fast 5V GPIO” of sub-chapter “5V/3.3V switchable Pads”
Changed note for parameter tTX_ASYM in table “Fast 3.3V GPIO” of sub-chapter “5V/3.3V switchable Pads”
Changed note for parameter tTX_ASYM in table “Slow 5V GPIO” of sub-chapter “5V/3.3V switchable Pads”
Changed note for parameter tTX_ASYM in table “Slow 3.3V GPIO” of sub-chapter “5V/3.3V switchable Pads”
Changed note for parameter tTX_ASYM in table “RFast 5V GPIO” of sub-chapter “5V/3.3V switchable Pads”
Changed note for parameter tTX_ASYM in table “RFast 3.3V pad” of sub-chapter “5V/3.3V switchable Pads”
Changed notes for parameter IOZ2 in table “ADC Reference Pads” of sub-chapter “5V/3.3V switchable
Pads”
–
–
Typos corrected in footnotes for table “LVDS – IEEE standard LVDS general purpose link (GPL)” in sub-
chapter “High performance LVDS Pads”
Added footnotes for table “LVDS – IEEE standard LVDS general purpose link (GPL)” in sub-chapter “High
performance LVDS Pads”
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Typo corrected for parameter dVCSD in table “VADC 5V” in sub-chapter “VADC Parameters”
Changed footnote 7) of table “VADC 5V” in sub-chapter “VADC Parameters”
Changed figure “Equivalent Circuitry for Analog Inputs” in sub-chapter “VADC Parameters”
Changed footnotes 3) and 6) for table "VADC 5V" in sub-chapter "VADC Parameters"
Changed value of parameter IRMS in table “DSADC 5V” in sub-chapter “DSADC Parameters”
Changed footnote 4) in sub-chapter “DSADC Parameters”
Changed spelling in footnote 2) in sub-chapter “MHz Oscillator”
Changed footnote 2) for table “Current Consumption” in sub-chapter “Power Supply Current”
Added footnote 9) for table “Current Consumption” in sub-chapter “Power Supply Current”
Typos corrected in sub-chapter “Calculating the 1.25V Current Consumption”
Added sentence to sub-chapter “Supply Ramp-up and Ramp-down Behavior”
Changed/added value for parameter tPI in table “Reset” for sub-chapter “Reset Timing”
Changed figure “DAP Timing” in sub-chapter “DAP Parameters”
Changed values (from Min. to Typ.) for parameter t7 in table “ETH MII Signal Timing Parameters” for sub-
chapter “ETH MII Parameters”
–
–
–
Changed symbols for parameters t13, t14, t15 in table “ETH RMII Signal Timing Parameters valid for 3.3V” in
sub-chapter “ETH RMII Parameters”
Changed value (from Min. to Typ.) for parameter t13 in table “ETH RMII Signal Timing Parameters valid for
3.3V” in sub-chapter “ETH RMII Parameters”
Added footnote 3) for table “ETH RMII Signal Timing Parameters valid for 3.3V” in sub-chapter “ETH RMII
Parameters”
–
–
Deleted parameter t81 in table “Skew Calibration Related” in sub-chapter “Radar Interface Timing”
Changed values for parameters t82 and t83 in table “Skew Calibration Related” in sub-chapter “Radar
Interface Timing”
–
–
Deleted notes for parameters t82 and t83 in table “Skew Calibration Related” in sub-chapter “Radar Interface
Timing”
Added footnotes to Max. Value of parameter tER_Dev in table “Flash” in sub-chapter “Flash Target
Parameters”
Data Sheet
546
V 1.2, 2021-03
OPEN MARKET VERSION
INFINEON [ Infineon ]
