欢迎访问ic37.com |
会员登录 免费注册
发布采购

PEB2091NV5.3 参数 Datasheet PDF下载

PEB2091NV5.3图片预览
型号: PEB2091NV5.3
PDF下载: 下载PDF文件 查看货源
内容描述: 集成电路通信( ISDN Echocancellation电路) [ICs for Communications(ISDN Echocancellation Circuit)]
分类和应用: 电信集成电路综合业务数字网通信
文件页数/大小: 299 页 / 1531 K
品牌: INFINEON [ Infineon ]
 浏览型号PEB2091NV5.3的Datasheet PDF文件第161页浏览型号PEB2091NV5.3的Datasheet PDF文件第162页浏览型号PEB2091NV5.3的Datasheet PDF文件第163页浏览型号PEB2091NV5.3的Datasheet PDF文件第164页浏览型号PEB2091NV5.3的Datasheet PDF文件第166页浏览型号PEB2091NV5.3的Datasheet PDF文件第167页浏览型号PEB2091NV5.3的Datasheet PDF文件第168页浏览型号PEB2091NV5.3的Datasheet PDF文件第169页  
PEB 2091  
PEF 2091  
Operational Description  
µP-SSP  
µP-DT  
µP-Send Single Pulses  
Applies only in microprocessor mode. Corresponds to the setting:  
STCR:TM1 = ’1’ and STCR:TM2 = ’1’. The function of this setting is the  
same as of the C/I-code SSP. C/I-message DR will be issued. See "Test  
Modes", page 52.  
µP-Data Through  
Applies only in microprocessor mode. This function is activated by setting:  
STCR:TM1 = ’0’ and STCR:TM2 = ’1’. The function of this setting is the  
same as of the C/I-code DT. See "Test Modes", page 52.  
U-Interface Events  
The signals SLx and TL received on the U-interface are defined in Table 28, page 125.  
ACT  
ACT-bit received from LT side.  
– ACT = 1 requests the IEC-Q to transmit transparently in both directions.  
As transparency in receive direction (U-interface to IOM®-2) is already  
performed when the Receiver is synchronized, the receipt of ACT = 1  
establishes transparency in transmit direction (IOM®-2 to U-interface),  
too. In the case of loop-backs, however, transparency in both directions  
of transmission is established when the Receiver is synchronized.  
– ACT = 0 indicates that the LT side has lost transparency.  
DEA-bit received from the LT side  
DEA  
UOA  
– DEA = 0 informs the IEC-Q that a deactivation procedure has been  
started by the LT side.  
– DEA = 1 reflects the case when DEA = 0 was detected by faults due to  
e.g. transmission errors and allows the IEC-Q to recover from this  
situation (see state ’Pend. Deact. U’).  
UOA-bit received from network side  
– UOA = 0 informs the IEC-Q that only the U-interface is to be activated.  
The S/T-interface must remain deactivated.  
– UOA = 1 enables the S/T-interface to activate.  
Loss of Framing on the U-interface  
LOF  
This condition is fulfilled if framing is lost for 576 ms. 576 ms are the upper  
limit. If the correlation between synchronization word and the input signal is  
not optimal, LOF may be issued earlier.  
LSEC  
Loss of Signal level behind the Echo Canceler  
Internal signal which indicates that the echo canceler has converged.  
Semiconductor Group  
165  
Data Sheet 01.99  
 复制成功!