iC-MSB
SAFETY
, iC-MSB2
SIN/COS SIGNAL CONDITIONER WITH 1Vpp DRIVER
Rev D2, Page 8/29
ELECTRICAL CHARACTERISTICS
Operating conditions: VDD = 4.3...5.5 V, Tj = -40...125 °C, IBN calibrated to 200 µA, reference point GNDS, unless otherwise stated.
Item
No.
Symbol
Parameter
Conditions
Min.
Vs() = VDD - V();
ADJ(8:0) = 0x11F, I() = -5 mA
ADJ(8:0) = 0x13F, I() = -10 mA
ADJ(8:0) = 0x15F, I() = -25 mA
ADJ(8:0) = 0x17F, I() = -50 mA
V() = 0 ... VDD - 1 V;
ADJ(8:0) = 0x11F
ADJ(8:0) = 0x13F
ADJ(8:0) = 0x15F
ADJ(8:0) = 0x17F
I(ACO): 0
→
90 % setpoint
Square control active, I(ACO): 50
→
100 %
setpoint
referenced to range ADJ(6:5)
referenced to range ADJ(6:5)
referenced to Vscq()
referenced to Vscq()
-10
-20
-50
-100
1
400
3
90
40
130
Typ.
Max.
Unit
Signal Level Controller ACO
601 Vs()hi
Saturation Voltage hi
at ACO vs. VDD
1
1
1
1
-5
-10
-25
-50
V
V
V
V
mA
mA
mA
mA
ms
µs
%Isc
%Isc
%Vpp
%Vpp
602
Isc()hi
Short-circuit Current hi in ACO
603
604
605
606
607
608
tr()
tset()
It()min
It()max
Vt()min
Vt()max
Current Rise Time in ACO
Current Settling Time in ACO
Control Range Monitoring 1:
lower limit
Control Range Monitoring 2:
upper limit
Signal Level Monitoring 1:
lower limit
Signal Level Monitoring 2:
upper limit
Permissible Test Current
Bias Current Source
Reference Voltage VPAH
Reference Voltage V05
Reference Voltage V025
Turn-on Threshold
(power-on release)
Turn-off Threshold
(power-down reset)
Threshold Hysteresis
Internal Clock Frequency
Saturation Voltage lo
Short-circuit Current lo
Input Threshold Voltage hi
Input Threshold Voltage lo
Input Hysteresis
Input Pull-up Current
Input Pull-Up Resistor
Pull-up Voltage
Test Mode Activation Threshold
Test Mode Disabling Threshold
Test Mode Hysteresis
Leakage Current
Test Current ERR
701
801
802
803
804
901
902
903
A01
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
I(ERR)
IBN()
VPAH
V05
V025
VDDon
VDDoff
VDDhys
fclk()
Vs()lo
Isc()
Vt()hi
Vt()lo
Vt()hys
Ipu()
Rpu()
Vpu()
VTMon
VTMoff
VTMhys
Ilk()
test mode activated
MODE(3:0) = 0x01, I(NC) vs. VDDS
referenced to GND
0
180
45
450
200
50
500
50
increasing voltage at VDD vs. GND
decreasing voltage at VDD vs. GND
VDDhys = VDDon
−
VDDoff
MODE(3:0) = 0x0A, fclk(NS)
vs. GND, I() = 4 mA
vs. GND; V(ERR)
≤
VDD
V(ERR) > VTMon
vs. GND
vs. GND
Vt()hys = Vt()hi
−
Vt()lo
V() = 0...VDD
−
1 V, EPU = 1
EPU = 0
Vpu() = VDD - V(), I() = -5 µA, EPU = 1
increasing voltage at ERR
decreasing voltage at ERR
VTMhys = VTMon
−
VTMoff
tristate or reversed supply voltage
VDD +
0.5
0.15
-1
0.3
-10
-50
0.8
300
-400
500
-300
500
0.4
VDD +
1.5
-200
4
2
2
3.7
3.2
0.3
120
160
200
0.4
4
3.5
4.3
3.8
1
220
55
550
mA
µA
%VDD
mV
%V05
V
V
V
kHz
V
mA
mA
V
V
mV
µA
kΩ
V
V
V
V
µA
Bias Current Source and Reference Voltages
Power-Down-Reset
Clock Oscillator
Error Signal Input/Output, Pin ERR
ICHAUS [ IC-HAUS GMBH ]
