欢迎访问ic37.com |
会员登录 免费注册
发布采购

IC-MSB2EVALMSB1D 参数 Datasheet PDF下载

IC-MSB2EVALMSB1D图片预览
型号: IC-MSB2EVALMSB1D
PDF下载: 下载PDF文件 查看货源
内容描述: SIN / COS信号调理与1Vpp典型DRIVER [SIN/COS SIGNAL CONDITIONER WITH 1Vpp DRIVER]
分类和应用: 驱动
文件页数/大小: 29 页 / 584 K
品牌: ICHAUS [ IC-HAUS GMBH ]
 浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第20页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第21页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第22页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第23页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第25页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第26页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第27页浏览型号IC-MSB2EVALMSB1D的Datasheet PDF文件第28页  
iC-MSBSAFETY, iC-MSB2  
SIN/COS SIGNAL CONDITIONER WITH 1Vpp DRIVER  
Rev D2, Page 24/29  
SIGNAL LEVEL CONTROL and SIGNAL MONITORING  
ADJ (6:5)  
Code  
00  
Adr 0x10, bit 5:4  
Function  
Via the controlled sensor current source (pin ACO)  
iC-MSB can keep the output signals for the ensuing  
sine/digital converter constant regardless of tempera-  
ture and aging effects by tracking the sensor supply.  
5 mA - Range  
10 mA - Range  
25 mA - Range  
50 mA - Range  
01  
10  
11  
Table 44: ACO Output Current Range (applies for con-  
trol modes and constant current source)  
Both the controller operating range and input signal  
amplitude for the controller are monitored and can  
be enabled for error messaging. A constant current  
source can be selected for the ACO output when set-  
ting the signal conditioning; the current range for the  
highside current source is adjusted using ADJ(6:5).  
ADJ (4:0)  
Code  
Adr 0x10, bit 3:0; Adr 0x0F, bit 7  
Square control ADJ(8:7) = 00  
Vpp() ca. 300 mV (60 %)  
0x00  
0x01  
Vpp() ca. 305 mV (61 %)  
77  
...  
Vpp() 300 mV 77(1.25Code)  
0x19  
...  
Vpp() ca. 500 mV (98 %)  
...  
0x1F  
Vpp() ca. 600 mV (120 %)  
Table 45: Vpp Setpoint For Square Control  
ADJ (4:0)  
Adr 0x10, bit 3:0; Adr 0x0F, bit 7  
Sum control ADJ(8:7) = 01  
VDC1 + VDC2 ca. 245 mV  
VDC1 + VDC2 ca. 249 mV  
Code  
0x00  
0x01  
77  
...  
VDC1 + VDC2 245mV 77(1.25Code)  
Figure 6: Signal level monitoring with square control  
(example for ADJ(8:0) = 0x19; see Elec.  
Char. Nos.607 and 608 regarding Vt()min  
resp. Vt()max)  
0x1F  
VDC1 + VDC2 ca. 490 mV  
Table 46: DC Setpoint For Sum Control  
ADJ (4:0)  
Code  
Adr 0x10, bit 3:0; Adr 0x0F, bit 7  
Constant current source ADJ(8:7) = 10  
I(ACO) ca. 3.125% Isc(ACO)  
0x00  
ADJ (8:7)  
Code  
00  
Adr 0x10, bit 7:6  
0x01  
I(ACO) ca. 6.25% Isc(ACO)  
Function  
...  
I(ACO) 3.125% (Code + 1) Isc(ACO)  
Sine/cosine square control  
Sum control  
01  
0x1F  
I(ACO) ca. 100% Isc(ACO)  
10  
Constant current source  
Not permitted (device test only)  
11  
Notes  
See Elec. Char. No. 602 for Isc(ACO)  
Table 43: Controller Operating Modes  
Table 47: I(ACO) With Constant Current Source  
 复制成功!