iC-MFL / iC-MFLT
8-/12-FOLD FAIL-SAFE LOGIC N-FET DRIVER
Rev C1, Page 6/13
ELECTRICAL CHARACTERISTICS
Operating Conditions: VCC = 5 V ±10 %, Tj = -40...125 °C unless otherwise stated
Item Symbol
No.
Parameter
Conditions
Tj
°C
Fig.
Unit
Min.
Typ.
Max.
Total Device
001 VCC
Permissible Supply Voltage
Supply Current in VCC
4.5
1.5
-50
5
5.5
V
002
I(VCC)
(No load)
iC-MFL
iC-MFLT
7
10
mA
mA
003 I(VCC)
Error Current in VCC
Current in GND
VCC = 5 V, one output at 18 V
mA
004
I(GND)
(No load)
iC-MFL
iC-MFLT
-6
-9
mA
mA
005
I(GNDR)
Current in GNDR
(No load, all OUTx = hi)
iC-MFL
-4
-6
-0.3
100
mA
mA
iC-MFLT
Current Driver OUT1...8/12
101
I(OUTx)
Current in I(OUTx)
V() = 18 V
VCC = 5 V
20
-3
mA
102 U(OUTx) permitted voltage
103 Vc()lo Clamp Voltage lo referenced to
T < 100 ms, duty cycle < 2 %
I() = -10 mA
18
V
V
-0.4
the lower voltage of GND, GNDR
104
105
Vs()hi
Vs()lo
Saturation Voltage hi referenced
to VCC
Vs()hi = VCC – V();
I() = -0.5 mA
I() = -2 mA
0.2
0.8
V
V
Saturation Voltage lo referenced
to GND
I() = 0.5 mA
I() = 2 mA
0.2
0.8
V
V
106 Rpd()
Pull-Down Resistor at OUTx
referenced to GNDR
V(GND) > Vtr(GND)
12
30
70
kΩ
107 Isc()lo
108 Isc()hi
109 Vsh()
Short circuit current lo
Short circuit current hi
V() = 0.8 V...VCC
2
3.6
-3
6
mA
mA
V
V() = 0...VCC – 0.8 V
-6
-2
Output Voltage at short circuit of At two different input signals hi
1.1
two outputs
and lo
Input IN1...8/12, EN
201 Vc()hi
Clamp Voltage hi
I() = 10 mA
I() = -10 mA
6
V
V
202 Vc()lo
Clamp Voltage lo referenced to
the lower voltage of GND, GNDR
-3
-0.4
203 Vt()hi
204 Vt()lo
Threshold Voltage hi
Threshold Voltage lo
Input Hysteresis
1.1
0.8
200
150
20
1.4
1.1
400
350
70
V
V
205 Vt()hys
206 Ipd1()
207 Ipd2()
208 Cin()
Vt()hys = Vt()hi – Vt()lo
0.4 V < V() < Vt()hi
V() > 1.4 V
mV
µA
µA
pF
µA
Pull-Down Current 1
Pull-Down Current 2
Input Capacitance
Input Leakage Current
4
4
225
45
20
209 Ileak()
Supply Monitor
301 VCCon
302 VCCoff
303 VCChys
VCC = 0 V, V() = 0...5.5 V
-10
10
Turn-On Threshold VCC
Turn-Off Threshold VCC
Hysteresis
3.7
3.2
4.4
4.1
V
V
Decreasing voltage VCC
VCChys = VCCon – VCCoff
100
200
600
mV
Ground Monitor GND, GNDR
401 Vtg()hi
Threshold Voltage hi GND Moni- Referenced to GNDR
tor
270
mV
mV
402 Vtg()lo
Threshold Voltage lo GND Moni- Referenced to GNDR
tor
50
5
403 Vtg()hys
404 Vtr()hi
Hysteresis
Vt()hys = Vt()hi - Vt()lo
80
mV
mv
Threshold Voltage hi GNDR Mon- Referenced to GND
itor
270
405 Vtr()lo
Threshold Voltage lo GNDR Mon- Referenced to GND
itor
50
mV
ICHAUS [ IC-HAUS GMBH ]
