IC-JE 参数 Datasheet PDF下载

iC-JE

PWM RELAY/SOLENOID DRIVER

Rev F1, Page 4/9

ELECTRICAL CHARACTERISTICS

Operating Conditions: VB = 10...45 V, LOUT = 0.01...10 H, RSET = 10...60 kΩ, Tj = -25...125 °C, unless otherwise noted.

LED connected or pin LED linked to GND (via ca. 500

Ω

resistor or capacitor).

Item

No.

001

002

003

004

005

006

007

Symbol

Parameter

Conditions

Tj

°C

Fig.

Min.

10

Outputs OUT, LED disabled

Output OUT enabled

I() = -4 mA, other Pins open

I(OUT) = 4 mA, other Pins open

Vc()hi = V(LED)

−

V(VB);

I(LED) = 4 mA, other Pins open

I(OUT) = 200 mA

I(OUT) = 300 mA

Increased Energising Current by

RC-circuit at ISET,

Hold Current 200 mA max.

104

105

106

107

108

109

110

111

201

202

203

204

205

206

207

208

209

210

PWMthi

Isc()

Vc()hi

Vc()hi

Vc()off

IIK()

twon()min

C()

Vt()on

Vt()off

Vt()hys

lpd()

Rpd()

Permissible Hold Current

Short-circuit Current

Clamp Voltage hi at

PWM-Free-Wheeling

Clamp Voltage hi at

PWM-Free-Wheeling

Clamp Voltage hi at Turn-off

Leakage Current

Permissible Load Capacitance

Threshold Voltage hi

Threshold Voltage lo

Hysteresis

Pull-down Current

Pull-down Resistor

Vt()hys = Vt()on

−

Vt()off

V(IN) = 4...45 V

V(IN) = 0...4 V

IN: lo

→

hi

IN: hi

→

lo

IN = VB, VB = VBoff

→

VBon

PWMOK = 1 before tpPMWlo

PWMOK = 0

65

130

100

200

2.6

1.7

0.7

50

20

2.85

2.0

0.85

100

50

V(OUT) = VB

Vc()hi = V(OUT)

−

VB; IN = hi,

I(OUT) = 200 mA

Vc()hi = V(OUT)

−

VB; IN = hi,

I(OUT) = 300 mA

Vc()hi = V(OUT)

−

VB;

IN: hi

→

lo, I(OUT) = 200 mA

IN = lo, V(OUT) = 0...VB

250

12

0.5

0.5

-1.4

48

60

0.3

57

71

1.4

Typ.

Max.

45

2

3

-0.3

V

mA

mA

V

V

V

V

Unit

Total Device

VB

I(VB)

I(VB)

Vc()lo

Vc()hi

Vc()hi

Vc()hi

Permissible Supply Voltage

Range

Supply Current in VB

Supply Current in VB

Clamp Voltage lo at all Pins

Clamp Voltage hi at OUT

Clamp Voltage hi at LED vs. VB

Clamp Voltage hi at VB, IN, ISET I() = 4 mA, other Pins open

Driver Output OUT

101

102

103

Vs()lo

Vs()lo

PWMthi

Saturation Voltage lo

Saturation Voltage lo

Permissible Energising Current

360

550

600

850

300

350

mV

mV

mA

mA

40

0.6

1

1

1.4

15

1

1.7

1.5

2

17

10

1000

1

3.2

2.3

1.1

200

80

20

10

40

135

270

mA

A

V

V

V

µA

ns

nF

V

V

V

µA

kΩ

µs

µs

µs

ms

ms

Minimum PWM Turn-on Duration IN = hi, ISET open

Input IN

tp(IN-OUT) Turn-on Delay

tp(IN-OUT) Turn-off Delay

tp(VB-

OUT)

Turn-on Delay when VB is

powered up

tp(IN-LED) Delay Time from IN to LED

(with light permanently on)

tp(IN-LED) Delay Time from IN to LED

(with light flashing)

Ipd()

Vs()lo

Ipu()

VBlo

VBon

VBoff

VBhys

Toff

Pull-down Current

Saturation Voltage lo

Pull-up Current

Permissible Supply Voltage for

Monitoring Function

Turn-on Threshold at VB

Undervoltage Threshold at VB

Hysteresis

Thermal Shutdown Temperature

Status Monitor LED

301

302

303

304

305

306

307

308

V(LED) = 5 V...VB

I(LED) = 200 µA

V(LED) = 0 V...(VB

−

1 V)

-20

6

7.6

Decreasing voltage VB

VBhys = VBon

−

VBoff

7.1

200

130

8

7.5

500

140

-100

3

5

8

0.4

-300

45

8.4

7.9

800

150

mA

V

µA

V

V

V

mV

°C