欢迎访问ic37.com |
会员登录 免费注册
发布采购

IBM25PPC970FX6TR348ET 参数 Datasheet PDF下载

IBM25PPC970FX6TR348ET图片预览
型号: IBM25PPC970FX6TR348ET
PDF下载: 下载PDF文件 查看货源
内容描述: [RISC Microprocessor, 64-Bit, 2000MHz, CMOS, CBGA576, 25 X 25 MM, 1 MM PITCH, ROHS COMPLIANT, CERAMIC, BGA-576]
分类和应用: 时钟外围集成电路
文件页数/大小: 74 页 / 3280 K
品牌: IBM [ IBM ]
 浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第14页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第15页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第16页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第17页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第19页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第20页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第21页浏览型号IBM25PPC970FX6TR348ET的Datasheet PDF文件第22页  
Data Sheet  
PowerPC 970FX  
Preliminary  
3.1.2 Recommended Operating Conditions  
Table 3-2. Recommended Operating Conditions  
Characteristic  
Symbol  
Value  
Unit  
V
Notes  
see Table 3-5,  
Table 3-6, Table 3-  
7 and Table 3-8  
Core supply voltage  
V
DD  
PLL supply voltage  
I/O supply voltage  
Input voltage  
AV  
OV  
2.775 ± 75mV  
1.5 ± 50mV  
V
V
V
DD  
DD  
IN  
V
GND to OV  
DD  
3.1.3 Package Thermal Characteristics  
Table 3-3. Package Thermal Characteristics  
Characteristic  
Symbol  
Value  
0.1  
Unit  
°C/W  
°C/W  
CBGA thermal conductance to back of die  
CBGA thermal conductance to board  
θ
JC  
θ
5.4  
JB  
3.1.4 DC Electrical Specifications  
Table 3-4. DC Electrical Specifications  
Voltage  
Characteristic  
Symbol  
Unit  
Notes  
Minimum  
Maximum  
OV + 0.3  
SYSCLK, SYSCLK input high voltage  
SYSCLK, SYSCLK input low voltage  
Elastic Input (EI) input high voltage  
0.7 x OV  
-0.3  
V
V
V
1
1
2
DD  
DD  
0.3 x OV  
DD  
VIH  
(0.5 x OV ) + 0.2  
DD  
Notes: See Table 3-2 on page 18 for recommended operating conditions.  
1. SYSCLK differential receiver requires HSTL differential signaling level. See the JEDEC HSTL standard.  
2. See the PowerPC 970FX Users Manual, Electrical Interface section. Minimum input must meet the EYE OPENING  
REQUIREMENTS of the link.  
3. The JTAG signals TDI, TMS, and TRST do not have internal pullups; therefore, pullup must be added on the board. Pullups  
should be added and adjusted according to the system implementation. These input/outputs meet the DC specification in the  
JEDEC standard JESD8-11 for 1.5V Normal Power Supply Range.  
4. A 100split terminator is the test load. Note a 40driver has an up level of 0.78 x OV for V  
and 0.22 x OV at V  
.
DD  
OH  
DD  
OL  
5. There are two open drain signals on this type of driver: CHKSTOP and I2CGO. The pullup for these nets depend on the t  
rise  
time requirement, net load, and topology. The following are two bounding suggestions based on a point-to-point 50net with  
two lengths (5cm and 61cm). A 33series source terminator was added in both runs. A net of 61cm or 24 inches is  
recommended.  
Examples:  
500Pullup DC Low Level 0.18V @ Receiver  
Trise 0.2V - 0.8V = 55ns @ 61cm  
Trise 0.2V - 0.8V = 10ns @ 5cm  
1KPullup DC Low Level 0.13V @ Receiver  
Trise 0.2V - 0.8V = 115ns @ 61cm  
Trise 0.2V - 0.8V = 20ns @ 5cm  
6. Capacitance values are guaranteed by design and characterization, and are not tested.  
Electrical and Thermal Characteristics  
October 14, 2005  
Page 18 of 74