欢迎访问ic37.com |
会员登录 免费注册
发布采购

IBM25PPC405GPR-3BB266C 参数 Datasheet PDF下载

IBM25PPC405GPR-3BB266C图片预览
型号: IBM25PPC405GPR-3BB266C
PDF下载: 下载PDF文件 查看货源
内容描述: [RISC Microprocessor, 32-Bit, 266MHz, CMOS, PBGA456, 35 MM, PLASTIC, BGA-456]
分类和应用: 时钟外围集成电路
文件页数/大小: 56 页 / 1071 K
品牌: IBM [ IBM ]
 浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第24页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第25页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第26页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第27页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第29页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第30页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第31页浏览型号IBM25PPC405GPR-3BB266C的Datasheet PDF文件第32页  
Preliminary  
PowerPC 405GPr Embedded Processor Data Sheet  
Signal List  
The following table provides a summary of the number of package pins associated with each functional  
interface group.  
Pin Summary  
Group  
PCI  
No. of Pins  
60  
18  
71  
96  
9
Ethernet  
SDRAM  
External peripheral  
External master  
Internal peripheral  
Interrupts  
15  
7
JTAG  
5
System  
18  
299  
32  
Total Signal Pins  
OV  
DD  
V
24  
59  
36  
6
DD  
Gnd  
Thermal (and Gnd)  
Reserved  
Total Pins  
456  
Multiplexed Pins  
In the table “Signal Functional Description” on page 30, each external signal is listed along with a short  
description of the signal function. Some signals are multiplexed on the same package pin (ball) so that the pin  
can be used for different functions. Multiplexed signals are shown as a default signal with a secondary signal  
in square brackets (for example, GPIO1[TS1E]). Active-low signals (for example, RAS) are marked with an  
overline.  
It is expected that in any single application a particular pin will always be programmed to serve the same  
function. The flexibility of multiplexing allows a single chip to offer a richer pin selection than would otherwise  
be possible.  
In addition to multiplexing, many pins are also multi-purpose. For example, the EBC peripheral controller  
address pins are used as outputs by the PPC405GPr to broadcast an address to external slave devices when  
the PPC405GPr has control of the external bus. When, during the course of normal chip operation, an  
external master gains ownership of the external bus, these same pins are used as inputs which are driven by  
the external master and received by the EBC in the PPC405GPr. In this example, the pins are also  
bidirectional, serving as both inputs and outputs.  
Intialization Strapping  
One group of pins is used as strapped inputs during system reset. These pins function as strapped inputs  
only during reset and are used for other functions during normal operation (see “Strapping” on page 51). Note  
that the use of these pins for strapping is not considered multiplexing since the strapping function is not  
programmable.  
28  
 复制成功!