欢迎访问ic37.com |
会员登录 免费注册
发布采购

RF02 参数 Datasheet PDF下载

RF02图片预览
型号: RF02
PDF下载: 下载PDF文件 查看货源
内容描述: 通用ISM频段FSK发射器 [Universal ISM Band FSK Transmitter]
分类和应用: ISM频段
文件页数/大小: 24 页 / 1085 K
品牌: HOPERF [ HOPERF ]
 浏览型号RF02的Datasheet PDF文件第8页浏览型号RF02的Datasheet PDF文件第9页浏览型号RF02的Datasheet PDF文件第10页浏览型号RF02的Datasheet PDF文件第11页浏览型号RF02的Datasheet PDF文件第13页浏览型号RF02的Datasheet PDF文件第14页浏览型号RF02的Datasheet PDF文件第15页浏览型号RF02的Datasheet PDF文件第16页  
RF02  
d2  
d1  
d0  
Clock Output  
Frequency [MHz]  
The resulting output frequency can be calculated as:  
fout = f0 – (-1)SIGN * (M + 1) * (30 kHz)  
where:  
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
1.25  
1.66  
2
f0 is the channel center frequency (see the next  
command)  
M is the three bit binary number <m2 : m0>  
SIGN = (ms) XOR (FSK input)  
Note:  
2.5  
3.33  
5
• Use M in a range from 0 to 6.  
10  
2. Power Management Command  
bit 15 14 13 12 11 10  
9
0
8
0
7
6
5
4
3
2
1
0
POR  
1
1
0
0
0
0
a1 a0 ex es ea eb et dc C000h  
Bits 5-0, enable the corresponding block of the transmitters, i.e. the crystal oscillator is enabled by  
the ex bit, the synthesizer by es, the power amplifier by ea and the low battery detector by eb, while the  
wake-up timer by et. The bit dc disables the clock output buffer.  
When receiving the Data Transmit Command, the chip supports automatic on/off control over the  
crystal oscillator, the PLL and the PA.  
If bit a1 is set, the crystal oscillator and the synthesizer are controlled automatically. Data Transmit  
Command starts up the crystal oscillator and as soon as a stable reference frequency is available the  
synthesizer starts. After a subsequent delay to allow locking of the PLL, if a0 is set the power amplifier is  
turned on as well.  
Note:  
To enable the automatic internal control of the crystal oscillator, the synthesizer and the power  
amplifier, the corresponding bits (ex, es, ea) must be zero in the Power Management Command.  
The ex bit should be set in the Power Management Command for the correct control of es and ea.  
The oscillator can be switched off by clearing the ex bit after the transmission.  
The Sleep Command can be used to indicate the end of the data transmission process.  
For processing the events caused by the peripheral blocks (POR, LBD or wake-up timer) the chip  
requires operation of the crystal oscillator. This operation is fully controlled internally, independently from  
the status of the ex bit, but if the dc bit is zero, the oscillator remains active until Sleep Command is  
issued. (This command can be considered as an event controller reset.)  
Tel: +86-755-82973805  
Fax: +86-755-82 E-mail: sales@hoperf.com http://www.hoperf.com