欢迎访问ic37.com |
会员登录 免费注册
发布采购

697LP4E 参数 Datasheet PDF下载

697LP4E图片预览
型号: 697LP4E
PDF下载: 下载PDF文件 查看货源
内容描述: 硅锗宽带直接正交调制器200 - 4000兆赫 [SiGe WIDEBAND DIRECT QUADRATURE MODULATOR, 200 - 4000 MHz]
分类和应用:
文件页数/大小: 8 页 / 306 K
品牌: HITTITE [ HITTITE MICROWAVE CORPORATION ]
 浏览型号697LP4E的Datasheet PDF文件第1页浏览型号697LP4E的Datasheet PDF文件第3页浏览型号697LP4E的Datasheet PDF文件第4页浏览型号697LP4E的Datasheet PDF文件第5页浏览型号697LP4E的Datasheet PDF文件第6页浏览型号697LP4E的Datasheet PDF文件第7页浏览型号697LP4E的Datasheet PDF文件第8页  
HMC697LP4 / 697LP4E  
v01.0309  
SiGe WIDEBAND DIRECT QUADRATURE  
MODULATOR, 200 - 4000 MHz  
Electrical Specifications, (continued)  
Parameter  
Conditions  
Min.  
200  
Typ.  
15  
Max.  
4000  
Units  
RF Output  
RF Frequency Range  
RF Return Loss  
MHz  
dB  
LO Input  
LO Frequency Range  
LO Input Power  
200  
-6  
4000  
+6  
MHz  
dBm  
dB  
0
LO Port Return Loss  
Baseband Input Port  
Baseband Input DC Voltage (Vbbdc)  
Baseband Input DC Bias Current (Ibbdc)  
12  
+1.4  
+4.5  
+1.5  
90  
+1.6  
+5.5  
V
10  
Single-ended.  
μA  
pF  
Single-ended Baseband Input Capacitance  
DC Power Requirements  
De-embed to the lead of the device.  
See Test Conditions Below  
4.5  
Supply Voltage (Vcc1, Vcc2)  
+5.0  
168  
V
Supply Current (Icc1 + Icc2)  
mA  
Test Conditions: Unless Otherwise Specified, the Following Test Conditions Were Used  
Parameter  
Condition  
+25 °C  
200 kHz  
+1.5V  
Temperature  
Baseband Input Frequency  
Baseband Input DC Voltage (Vbbdc)  
Baseband Input AC Voltage  
(Peak to Peak Differential, I and Q)  
1.6V  
Baseband Input AC Voltage for OIP3 Measurement (Peak to Peak Differential, I and Q)  
800 mV per tone @ 150 & 250 kHz  
Frequency Offset for Output Noise Measurements  
Supply (Vcc1, Vcc2)  
20 MHz  
+5.0V  
LO Input Power  
0 dBm  
LO Input Mode  
Single-Ended through LOP  
Mounting Configuration  
Refer to HMC697LP4E Application Schematic Herein  
Uncalibrated  
Sideband & Carrier Feedthrough  
Calibrated vs. Uncalibrated Test Results  
During the Uncalibrated Sideband and Carrier Suppression tests, care is taken to ensure that the I/Q signal paths from  
the Vector Signal Generator (VSG) to the Device Under Test (DUT) are equal. The “Uncalibrated, +25 °C” Sideband  
and Carrier Suppression plots were measured at room temperature, while the “Uncalibrated, over Temperature”  
Sideband and Carrier Suppression plots represent the worst case uncalibrated suppression levels measured at T=  
-40 °C, +25 °C, and +85 °C.  
The “Calibrated, + 25 °C” Sideband Suppression data was plotted after a manual adjustment of the I/Q amplitude  
balance and I/Q phase offset (skew) at +25 °C, and at each LO input power level. The +25 °C adjustment settings  
were held constant during tests over temperature. The “Calibrated, over Temperature” plots represent the worst case  
calibrated Sideband Suppression levels at T= -40 °C, +25 °C, and +85 °C.  
The “Calibrated, +25 °C” Carrier Suppression data was plotted after a manual adjustment of the Ip/In & Qp/Qn DC  
offsets at +25 °C, and at each LO input power level. The +25 °C adjustment settings were held constant during tests  
over temperature. The “Calibrated, over Temperature” plots represent the worst case Carrier Suppression levels  
measured at T= -40 °C, +25 °C, and +85 °C.  
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:  
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373  
Order On-line at www.hittite.com  
10 - 77