欢迎访问ic37.com |
会员登录 免费注册
发布采购

PLCC6-0.5W-W3 参数 Datasheet PDF下载

PLCC6-0.5W-W3图片预览
型号: PLCC6-0.5W-W3
PDF下载: 下载PDF文件 查看货源
内容描述: [Lens Type]
分类和应用:
文件页数/大小: 12 页 / 1816 K
品牌: HB [ HB ELECTRONIC COMPONENTS ]
 浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第4页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第5页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第6页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第7页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第8页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第9页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第10页浏览型号PLCC6-0.5W-W3的Datasheet PDF文件第11页  
Hebei I.T. (Shanghai) Co., Ltd.  
PLCC6-0.5W-W3  
型号:  
10.4.3 Hand SolderingNot Recommended/手工焊接(不推荐)  
Soldering iron/烙铁焊接300 degrees C max/不超过300℃5 seconds max/不超过5s;  
once/允许1次.  
10.5 Cleaning/清洗  
It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. It  
should be confirmed beforehand whether the solvents will dissolve the package the resin or not  
when using other solvents. Please do not clean the LEDs by the ultrasonic. If it is absolutely  
necessary, the influence of ultrasonic cleaning on the LEDs depends on ultrasonic power and the  
assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage  
to the LEDs will occur.  
建议使用酒精作为溶剂清洗LEDs。若要使用其他溶剂,应该预先证实是否能溶化封装  
料。请不要使用超声波清洗LEDS,如果一定要使用超声波清洗,则一定要注意超声波的  
功率和超声条件。在清洗作业前,必须预先实验确认对LEDS无任何的伤害。  
10.6 Static Electricity/静电  
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the  
LEDs. All devices, equipment and machinery must be properly grounded. It is recommended that  
precautions be taken against surge voltage to the equipment that mounts the LEDs.  
在接触LEDs时,建议使用防静电手腕带或防静电手套。所有的器件、设备和机器必须  
有可靠的接地。对所有LEDs接触的设备,建议采取预防措施消除冲击电压。  
10.7 Others/其他  
The LED light output is strong enough to injure human eyes. Precautions must be taken to  
prevent looking directly at the LEDs with unaided eyes for more than a few seconds.  
LED的光辐射足够强时,会对人眼造成伤害。若眼睛要直接看LED,并且要一定的时  
间,则必须采取相应防护措施。  
www.ledz.com  
Page 12 of 12