Flat panel sensor
s
System requirements
C7942CK-12
To operate C7942CK-12 at full performance, the following system and peripherals are required.
· PC: IBM compatible PC running on Windows XP
· Digital frame grabber card: Monochrome 16 bits or more, pixel clock 16 MHz or more, RS-422 interface synchronous signal (See
the frame grabber manual.)
The National Instruments IMAQ PCI-1424 (NI parts No. 777662-01) frame grabber with optional memory 64 MB (NI parts No.
920130-64) has been verified to successfully acquire 12-bit digital images from C7942CK-12. You can utilize the demonstration
software that comes with the frame grabber as a simple viewer, to acquire and save an image. To do so, refer to the frame
grabber user’s guide for how to use the camera information file for the demonstration software.
· Power source: A.vdd = +5.0 ± 0.1 V (700 mA), D.vdd = +5.0 ± 0.1 V (1000 mA), V (±7.5) = ±7.5 ± 0.5 V (±100 mA)
Please use a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an
FGG.2B.307.CLAD92Z plug at one end and open at the other end; 2 m; see Table 2.), an external trigger cable (terminated with
an FFA.0S.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes
supplied with C7942CK-12. An optional frame grabber cable for interface with the 36-pin receptacle (see Table 1) on C7942CK-
12 is also available for synchronous signal, video output and external control.
The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the
flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set
0.1 V higher than the voltage specified above.
Install a noise filter on the AC power input line to prevent surges on the AC line.
To supply the synchronous signal through ExtTrgGrb, apply high level of TTL to ExtTrgLemo and IntExt, or leave them without
connection. On the contrary, to use ExtTrgLemo, set high level to ExtTrgGrb and IntExt, or leave them without connection. The
earth terminal must be connected to a stable earth point to eliminate noise from surroundings.
Table 1: Pin assignm ent of 36-pin receptacle
Pin No.
Signal
Pin No.
1
Data12+ (MSB)
19
2
Data11+
20
3
Data10+
21
4
Data9+
22
5
Data8+
23
6
Data7+
24
7
Data6+
25
8
Data5+
26
9
Data4+
27
10
Data3+
28
11
Data2+
29
12
Data1+ (LSB)
30
13
bin0 (TTL)
31
14
bin1 (TTL)
32
15
ExtTrgGrb (TTL)
33
16
Vsync+
34
17
Hsync+
35
18
Pclk+
36
Unless otherwise noted, signal level is RS-422.
36-pin receptacle: TX20A-36R-D2GF1-A1L made by JAE (Japan Aviation Electronics Industry limited)
Mating plug: TX20A-36PH1-D2P1-D1E made by JAE (Japan Aviation Electronics Industry limited)
Signal
Data12- (MSB)
Data11-
Data10-
Data9-
Data8-
Data7-
Data6-
Data5-
Data4-
Data3-
Data2-
Data1- (LSB)
GND
GND
IntExt (TTL)
Vsync-
Hsync-
Pclk-
Table 2: Power pin assignment and cable color
Pin No.
Color
1
Brown
2
Red
3
Orange
4
Yellow
5
Green
6
Blue
7
Purple
Shield
-
7-pin power receptacle: ECG.2B.307.CLV made by LEMO S. A.
Mating power plug: FGG.2B.307.CLAD92Z made by LEMO S. A.
Signal
+7.5 V
Analog GND
-7.5 V
Analog GND
Analog +5 V
Digital GND
Digital +5 V
Analog GND
Table 3: External trigger pin assignm ent and cable color
Pin No.
Color
1
Red
2
Black
Shield
-
2-pin receptacle: ECP.0S.302.DLL made by LEMO S. A
Mating plug: FFA.0S.302.CLAC37 made by LEMO S. A.
Signal
ExtTrgLemo (TTL)
Signal GND
Analog GND
4
HAMAMATSU [ HAMAMATSU CORPORATION ]
