欢迎访问ic37.com |
会员登录 免费注册
发布采购

GAMW1V840MET 参数 Datasheet PDF下载

GAMW1V840MET图片预览
型号: GAMW1V840MET
PDF下载: 下载PDF文件 查看货源
内容描述: 48V输入, 1.8VDC , 40A输出 [48V Input, 1.8VDC, 40A Output]
分类和应用:
文件页数/大小: 7 页 / 985 K
品牌: GALAXY [ GALAXY POWER, INC. ]
 浏览型号GAMW1V840MET的Datasheet PDF文件第1页浏览型号GAMW1V840MET的Datasheet PDF文件第2页浏览型号GAMW1V840MET的Datasheet PDF文件第3页浏览型号GAMW1V840MET的Datasheet PDF文件第5页浏览型号GAMW1V840MET的Datasheet PDF文件第6页浏览型号GAMW1V840MET的Datasheet PDF文件第7页  
Application Notes  
Output Over Voltage Protection:  
Trim:  
The output voltage is constantly monitored by the  
microprocessor with a redundant secondary-side  
measurement circuit that both shuts down the duty  
cycle and triggers the microprocessor to shut down.  
If the output voltage exceeds the over-voltage specifi-  
cation, the microprocessor will latch the converter off.  
To turn the converter on requires either cycling the  
ON/OFF pin or power to the converter. This ad-  
vanced feature prevents the converter from damaging  
the load if there is a converter failure or application  
error. If non-latching is required, consult factory.  
To trim the output voltage higher, connect the  
required trim resistor from the Trim pin to the  
+Sense pin. To trim the output voltage lower, con-  
nect the required trim resistor from the Trim pin to  
the –Sense pin.  
Trim-up  
1.8 (100+%) (100+2%)  
RTRIM-UP  
=
5.11kΩ  
{
}
1.225%  
%  
Thermal Shutdown:  
1.8V Trim-up  
The printed circuit board temperature is measured  
using a semiconductor sensor. If the maximum rated  
temperature is exceeded, the converter is latched off.  
To re-enable the converter requires cycling the ON/  
OFF pin or power to the converter. If non-latching is  
required, consult factory.  
1000  
100  
Control Options:  
As the behavior of the circuit is determined by  
firmware in the microcontroller, specific customer  
requirements such as  
10  
0
2
3
4
5
6
7
8
9
10  
1
Increase in Output Voltage (%)  
• non-latching thermal protection  
• custom valid input voltage range  
• controlled delay from initiating an ON/OFF signal  
for power sequencing  
can be accomplished with no change to hardware.  
The standard behavior was chosen based on system  
design experience but we understand that customers  
often have their own requirements.  
Trim-down  
100  
%  
RTRIM-DOWN  
=
– 2 5.11kΩ  
{ }  
Please consult Galaxy Power for your special needs.  
Trim-down  
Remote Sense:  
1000  
The output voltage is regulated at the point where  
the sense pins connect to the power output pins.  
Total sense compensation should not exceed 0.4V or  
10% of Vout, whichever is greater.  
100  
Safety:  
An external input fuse must always be used to meet  
these safety requirements.  
10  
0
External Output Trimming  
2
3
4
5
6
7
8
9
10  
1
Decrease in Output Voltage (%)  
+ Sense  
Trim  
– Sense  
GAMW1V840 – 4  
WWW.GALAXYPWR.COM  
Part No. 02-GAM-05 Rev. 1.0 – 042805  
Galaxy Power Inc. 155 Flanders Road Westborough, MA 01581 Telephone: 508-870-9775 Fax: 508-870-9796 e-mail: info@galaxypwr.com