欢迎访问ic37.com |
会员登录 免费注册
发布采购

UMFT221XA-01 参数 Datasheet PDF下载

UMFT221XA-01图片预览
型号: UMFT221XA-01
PDF下载: 下载PDF文件 查看货源
内容描述: [UMFT230XA USB to Basic UART Development Module]
分类和应用:
文件页数/大小: 21 页 / 692 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号UMFT221XA-01的Datasheet PDF文件第13页浏览型号UMFT221XA-01的Datasheet PDF文件第14页浏览型号UMFT221XA-01的Datasheet PDF文件第15页浏览型号UMFT221XA-01的Datasheet PDF文件第16页浏览型号UMFT221XA-01的Datasheet PDF文件第18页浏览型号UMFT221XA-01的Datasheet PDF文件第19页浏览型号UMFT221XA-01的Datasheet PDF文件第20页浏览型号UMFT221XA-01的Datasheet PDF文件第21页  
UMFT230XA Datasheet  
Version 1.4  
Document Reference No.: FT_000519 Clearance No.: FTDI#269  
7 Internal MTPROM Configuration  
Following a power-on reset or a USB reset the FT230X will scan its internal MTP ROM and read the USB  
configuration descriptors stored there. The default values programmed into the internal MTP ROM in the  
FT230XQ used on the UMFT230XA are shown in Table 8.1.  
Parameter  
USB VendorID (VID)  
USB Product UD (PID)  
Serial Number Enabled?  
Value  
0403h  
6015h  
Yes  
Notes  
FTDI default VID (hex)  
FTDI default PID (hex)  
A unique serial number is generatedand programmed into  
the, TP ROM during final test of the module.  
Serial Number  
See Note  
Disabled  
Enabling this option will make the device pull down on the  
UART interface lines whenthe power is shut off (PWREN#  
is high).  
Pull down I/O Pins in USB  
Suspend  
ManufacturerName  
Product Description  
Max Bus PowerCurrent  
Power Source  
FTDI  
UMFT230XA  
90mA  
Bus Powered  
FT230X  
Device Type  
Returns USB 2.0 device descriptionto the host. Note: The  
device is a USB 2.0 Full Speed device (12Mb/s)as opposed  
to a USB 2.0 High Speeddevice (480Mb/s).  
USB Version  
0200  
Taking RI# low will wake up the USB host controllerfrom  
suspend.  
Remote Wake Up  
High Current I/Os  
Load VCP Driver  
Enabled  
Disabled  
Enabled  
Enables the high drive level onthe UARTand CBUS I/O  
pins.  
Makes the device load the CVP driver interface forthe  
device.  
CBUS0  
GPIO  
GPIO  
CBUS1  
CBUS2  
GPIO  
CBUS3  
GPIO  
Invert UART  
Disabled  
Signal on this pin becomesTXD# if enable.  
Table 7.1 Default Internal MTP ROM Configuration  
The internal MTP ROM in the FT230X can be programmed over USB using the utility program FT_PROG.  
FT_PROG can be downloaded from the www.ftdichip.com. Users who do not have their own USB vendor  
ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of  
unique PIDs. Contact FTDI Support (support1@ftdichip.com) for this service, also see TN_100 and  
TN_101.  
Copyright © Future Technology Devices International Limited  
17