欢迎访问ic37.com |
会员登录 免费注册
发布采购

FT240XS-R 参数 Datasheet PDF下载

FT240XS-R图片预览
型号: FT240XS-R
PDF下载: 下载PDF文件 查看货源
内容描述: [USB 8-BIT FIFO IC]
分类和应用: 先进先出芯片
文件页数/大小: 40 页 / 754 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号FT240XS-R的Datasheet PDF文件第19页浏览型号FT240XS-R的Datasheet PDF文件第20页浏览型号FT240XS-R的Datasheet PDF文件第21页浏览型号FT240XS-R的Datasheet PDF文件第22页浏览型号FT240XS-R的Datasheet PDF文件第24页浏览型号FT240XS-R的Datasheet PDF文件第25页浏览型号FT240XS-R的Datasheet PDF文件第26页浏览型号FT240XS-R的Datasheet PDF文件第27页  
FT240X USB 8-BIT FIFO IC Datasheet  
Version 1.3  
Document No.: FT_000626 Clearance No.: FTDI# 259  
6.2 Self Powered Configuration  
VCC(3.3-5.25V)  
1
VCC  
27R  
2
3
USBDM  
27R  
USBDP  
4
47pF  
47pF  
FT240X  
4k7  
5
VBUS_SENSE  
SHIELD  
VCCIO  
RESET#  
GND  
10k  
GND  
3V3OUT  
D
D
N
N
G
A
G
GND  
VCC  
100nF  
100nF  
100nF  
+
4.7uF  
GND  
GND  
Figure 6.2 Self Powered Configuration  
Figure 6.2 illustrates the FT240X in a typical USB self powered configuration. A USB self powered device  
gets its power from its own power supply, VCC, and does not draw current from the USB bus. The basic  
rules for USB self powered devices are as follows –  
i)  
A self powered device should not force current down the USB bus when the USB host or hub  
controller is powered down.  
ii)  
iii)  
A self powered device can use as much current as it needs during normal operation and USB  
suspend as it has its own power supply.  
A self powered device can be used with any USB host, a bus powered USB hub or a self  
powered USB hub.  
The power descriptor in the internal MTP memory of the FT240X should be programmed to a value of  
zero (self powered).  
In order to comply with the first requirement above, the USB bus power (pin 1) is used to control the  
VBUS_Sense pin of the FT240X device. When the USB host or hub is powered up an internal 1.5kΩ  
resistor on USBDP is pulled up to +3.3V, thus identifying the device as a full speed device to the USB  
host or hub. When the USB host or hub is powered off, VBUS_Sense pin will be low and the FT240X is  
held in a suspend state. In this state the internal 1.5kΩ resistor is not pulled up to any power supply  
(hub or host is powered down), so no current flows down USBDP via the 1.5kΩ pull-up resistor. Failure to  
do this may cause some USB host or hub controllers to power up erratically.  
Figure 6.3 illustrates a self powered design which has a +3.3V to +5.25V supply.  
Note:  
1. When the FT240X is in reset, the interface I/O pins are tri-stated. Input pins have internal 200kΩ  
pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic.  
Copyright © 2013 Future Technology Devices International Limited  
23  
 
 
 复制成功!