ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. Dynamic Electrical Characteristics
Characteristics noted under conditions 6.0 V ≤ VPWR ≤ 27 V, 4.5 V ≤ VDD ≤ 5.5 V, -40°C ≤ TA ≤ 125°C, GND = 0 V unless
otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless
otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER OUTPUT TIMING (HS0, HS1, HS2, HS3)
Output Rising Slow Slew Rate A (DICR D3 = 0) (19)
SR
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
µs
RA_SLOW
SR
RB_SLOW
9.0 V < V
< 16 V
0.1
0.015
0.5
0.3
0.05
1.5
0.3
0.3
0.05
1.5
0.3
30
0.75
0.15
3.0
PWR
Output Rising Slow Slew Rate B (DICR D3 = 0) (20)
9.0 V < V < 16 V
PWR
Output Rising Fast Slew Rate A (DICR D3 = 1) (19)
SR
SR
SR
RA_FAST
RB_FAST
9.0 V < V < 16 V
PWR
Output Rising Fast Slew Rate B (DICR D3 = 1) (20)
9.0 V < V < 16 V
0.025
0.1
1.0
PWR
Output Falling Slow Slew Rate A (DICR D3 = 0) (19)
FA_SLOW
FB_SLOW
9.0 V < V < 16 V
0.75
0.15
3.0
PWR
Output Falling Slow Slew Rate B (DICR D3 = 0) (20)
SR
9.0 V < V < 16 V
0.015
0.5
PWR
Output Falling Fast Slew Rate A (DICR D3 = 1) (19)
SR
FA_FAST
FB_FAST
9.0 V < V < 16 V
PWR
Output Falling Fast Slew Rate B (DICR D3 = 1) (20)
SR
9.0 V < V < 16 V
0.025
2.0
1.0
PWR
Output Turn-ON Delay Time in Slow Slew Rate (21)
t
DLY_SLOW(ON)
DICR = 0
200
100
800
400
Output Turn-ON Delay Time in Fast Slew Rate (21)
t
µs
DLY_FAST(ON)
DICR = 1
1.0
6.0
200
50
Output Turn-OFF Delay Time in Slow Slew Rate Mode (22)
tDLY_SLOW(OF
µs
F)
DICR = 0
40
Output Turn-OFF Delay Time in Fast Slew Rate Mode (22)
tDLY_FAST(OFF)
µs
DICR = 1
20
Overcurrent Low Detection Blanking Time
OCLT[1:0]: 00
ms
tOCL0
tOCL1
tOCL2
tOCL3
108
–
155
–
202
–
OCLT[1:0]: 01 (23)
OCLT[1:0]: 10
55
75
95
0.3
OCLT[1:0]: 11
0.08
0.15
Notes
19. Rise and Fall Slew Rates A measured across a 5.0 Ω resistive load at high-side output = 0.5 V to V
-3.5 V (see Figure 4, page 12).
PWR
These parameters are guaranteed by process monitoring.
20. Rise and Fall Slew Rates B measured across a 5.0 Ω resistive load at high-side output = 0.5 V to V
-3.5 V (see Figure 4). These
PWR
parameters are guaranteed by process monitoring.
21. Turn-ON delay time measured from rising edge of any signal (IN[0:3], SCLK, CS) that would turn the output ON to V
= 0.5 V with
HS[0:3]
R = 5.0 Ω resistive load.
L
22. Turn-OFF delay time measured from falling edge of any signal (IN[0:3], SCLK, CS) that would turn the output OFF to V
= V
-
PWR
HS[0:3]
0.5 V with R = 5.0 Ω resistive load.
L
23. This logical bit is not defined. Do not use.
33874
Analog Integrated Circuit Device Data
Freescale Semiconductor
10
FREESCALE [ Freescale ]
