欢迎访问ic37.com |
会员登录 免费注册
发布采购

V23836-C18-C63 参数 Datasheet PDF下载

V23836-C18-C63图片预览
型号: V23836-C18-C63
PDF下载: 下载PDF文件 查看货源
内容描述: 1X9收发器,双工SC插座单模1310nm 21公里SONET OC - 3 / SDH STM - 1 [1x9 Transceiver with Duplex SC Receptacle Single Mode 1310 nm 21 km SONET OC-3/SDH STM-1]
分类和应用: 光纤插座
文件页数/大小: 13 页 / 217 K
品牌: FINISAR [ FINISAR CORPORATION. ]
 浏览型号V23836-C18-C63的Datasheet PDF文件第4页浏览型号V23836-C18-C63的Datasheet PDF文件第5页浏览型号V23836-C18-C63的Datasheet PDF文件第6页浏览型号V23836-C18-C63的Datasheet PDF文件第7页浏览型号V23836-C18-C63的Datasheet PDF文件第9页浏览型号V23836-C18-C63的Datasheet PDF文件第10页浏览型号V23836-C18-C63的Datasheet PDF文件第11页浏览型号V23836-C18-C63的Datasheet PDF文件第12页  
V23836-C18-C63, V23836-C18-C363 Product Specification – September 2004  
Receiver Electro-Optical Characteristics  
Parameter  
Symbol  
Values  
Unit  
min.  
typ. max.  
Sensitivity (Average Power)1)  
PIN  
dBm  
5 V  
3.3 V  
–36 –28  
–31  
Saturation (Average Power)  
PSAT  
–8  
dBm  
dBm  
dBm  
dB  
Signal Detect Assert Level2)  
Signal Detect Deassert Level3)  
Signal Detect Hysteresis  
Signal Detect Assert Time  
Signal Detect Deassert Time  
Output Low Voltage4)  
PSDA  
–34  
PSDD  
–44  
1
PSDAPSDD  
tASS  
2
5
75  
80  
100  
350  
µs  
tDAS  
µs  
VOLVCC  
VOHVCC  
–2000  
–1100  
–1580 mV  
Output High Voltage4)  
–740  
mV  
ns  
Output Data Rise/Fall Time, 20% - 80% tR, tF  
1.6  
10  
Output SD Rise/Fall Time  
40  
ns  
Notes:  
1) Minimum average optical power at which the BER is less than 1x10–10 or lower. Measured with a 223–1 NRZPRBS as  
recommended by ANSI T1E1.2, SONET OC-3 and ITU-T G.957. BOL value –31 dBm max.  
2) An increase in optical power of data signal above the specified level will cause the Signal Detect to switch from a low state to a  
high state.  
3) A decrease in optical power of data signal below the specified level will cause the Signal Detect to switch froma high state to a low  
state.  
4) DC/DC, PECL for Signal Detect, PECL compatible. Load is 50into VCC–2 V for data, 510 to VEE for SignalDetect. Measured  
under DC conditions. For dynamic measurements a tolerance of 50 mV should be added.VCC = 3.3 V. TAMB = 25°C.  
© Finisar Corporation September 10, 2004 Rev. A Preliminary Data  
8