FTLF8524P2xNy Pluggable SFP Product Specification – March 2005
IV.
Optical Characteristics
(T
OP
= -20 to 85
°
C, V
CC
= 3. 00 to 3.60 Volts)
Parameter
Symbol
P
OUT
λ
σ
OMA
OMA
OMA
t
r
/ t
f
RIN
TX
∆
DJ
TX
∆
DJ
TX
∆
TJ
TX
∆
TJ
ER
Min
-9
830
247
196
156
90
-118
56.5
28.2
119
56.5
9
45%
RxSENS
RxSENS
RxSENS
RxSENS
0.055
0.096
0.138
Rx
MAX
λ
C
LOS
D
LOS
A
770
12
-30
0.5
-13.5
0
1500
2500
860
-20
-20
-18
-15
-20
dBm
dBm
dBm
dBm
mW
mW
mW
dBm
dBm
MHz
MHz
nm
dB
dBm
dBm
dB
7
7
7
8
9
9
9
10
11
12
Typ
Max
-2.5
860
0.85
Unit
dBm
nm
nm
µW
µW
µW
ps
dB/Hz
ps
ps
ps
ps
dB
Ref.
1
Transmitter
Output Opt. Pwr: 50 or 62.5 MMF
Optical Wavelength
Spectral Width
Optical Modulation Amplitude @ 4.25 Gb/s
Optical Modulation Amplitude @ 2.125 Gb/s
Optical Modulation Amplitude @ 1.0625 Gb/s
Optical Rise/Fall Time
Relative Intensity Noise
Deterministic Jitter Contribution @ 2.125 Gb/s
Deterministic Jitter Contribution @ 4.25 Gb/s
Total Jitter Contribution @ 2.125 Gb/s
Total Jitter Contribution @ 4.25 Gb/s
Extinction Ratio @ 1.25 Gb/s
Mask Margin
Receiver
Receiver Sensitivity = 1.0625 Gb/s
Receiver Sensitivity = 2.125 Gb/s
Receiver Sensitivity = 4.25 Gb/s
Receiver Sensitivity = 1.25 Gb/s
Stressed RX sens. =1.0625 Gb/s
Stressed RX sens. =2.125 Gb/s
Stressed Rx sens. = 4.25 Gb/s
Stressed RX sens. =1.25 Gb/s
Average Receiver Power
Receiver Elec. 3 dB cutoff frequency
Receiver Elec. 3 dB cutoff frequency
Optical Center Wavelength
Optical Return Loss
LOS De-Assert
LOS Assert
LOS Hysteresis
2
2
2
3
4
4
5
5
6
Notes:
1. Class 1 Laser Safety per FDA/CDRH, and EN (IEC) 60825 laser safety standards.
2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average
power.
3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and
∆
DJ.
5. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
TJ
OUT
=
DJ
IN
+ ∆
DJ
+
6.
7.
8.
9.
(
TJ
IN
−
DJ
IN
)
+
(
∆
TJ
− ∆
DJ
)
2
2
Applicable for Rate Selectable version only in low bandwidth mode.
Specifications are for 50 micro-meter or 62.5 micro-meter fiber.
As measured with 9dB extinction ratio.
Measured with conformance signals defined in FC-PI-2 Rev. 7.0 specifications.
Finisar Corporation March 14, 2005 Rev.I
Page 4
FINISAR [ FINISAR CORPORATION. ]
