100LVEL16
Absolute Maximum Ratings
(Note 1)
PECL Supply Voltage (V
CC
) V
EE
=
0V
NECL Supply Voltage (V
EE
) V
CC
=
0V
PECL DC Input Voltage (V
I
) V
EE
=
0V
NECL DC Input Voltage (V
I
) V
CC
=
0V
DC Output Current (I
OUT
)
Continuous
Surge
V
BB
Sink/Source Current (I
BB
)
Storage Temperature (T
STG
)
50 mA
100 mA
0.0V to
+
8.0V
0.0V to
−
8.0V
0.0V to
+
6.0V
0.0V to
−
6.0V
Recommended Operating
Conditions
PECL Power Supply
(V
EE
=
0V)
NECL Power Supply
(V
CC
=
0V)
Free Air Operating Temperature (T
A
)
V
EE
= −
3.8V to
−
3.0V
V
CC
=
3.0V to 3.8V
−
40
°
C to
+
85
°
C
±
0.5 mA
−
65
°
C to
+
150
°
C
Note 1:
The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
LVPECL DC Electrical Characteristics
V
CC
=
3.3V; V
EE
=
0.0V (Note 2)
Symbol
I
EE
V
OH
V
OL
V
IH
V
IL
V
BB
V
IHCMR
Parameter
Power Supply Current
Output HIGH Voltage (Note 3)
Output LOW Voltage (Note 3)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 4)
V
PP
<
500mV
V
PP
≥
500mV
I
IH
I
IL
Input HIGH Current (Note 5)
Input LOW Current (Note 5)
D
D
0.5
−600
1.2
1.5
2.9
2.9
150
0.5
−600
1.1
1.4
2.9
2.9
150
0.5
−600
1.1
1.4
2.9
2.9
150
V
µA
µA
2215
1470
2135
1490
1.92
−40°C
Min
Typ
17
2295
1605
Max
23
2420
1745
2420
1825
2.04
2275
1490
2135
1490
1.92
Min
25°C
Typ
17
2345
1595
Max
23
2420
1680
2420
1825
2.04
2275
1490
2135
1490
1.92
Min
85°C
Typ
18
2345
1595
Max
24
2420
1680
2420
1825
2.04
Units
mA
mV
mV
mV
mV
V
Note 2:
Input and output parameters vary 1 to 1 with V
CC
. V
EE
can vary
±0.3V.
Note 3:
Outputs are terminated through a 50Ω Resistor to V
CC
−
2.0V.
Note 4:
V
IHCMR
minimum varies 1 to 1 with V
EE
. V
IHCMR
maximum varies 1 to 1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the dif-
ferential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between V
PPMIN
and
1V.
Note 5:
Absolute value of the input HIGH and LOW current should not exceed the absolute value of the stated Min or Max specification.
Note:
Devices are designed to meet the DC specifications after thermal equilibrium has been established. Circuit is tested with air flow greater than
500LFPM maintained.
www.fairchildsemi.com
2