欢迎访问ic37.com |
会员登录 免费注册
发布采购

EX29DS160-90RTCI 参数 Datasheet PDF下载

EX29DS160-90RTCI图片预览
型号: EX29DS160-90RTCI
PDF下载: 下载PDF文件 查看货源
内容描述: 32兆( 4M ×8 / 2M ×16 )的CMOS 3.0伏只,同时操作闪存 [32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory]
分类和应用: 闪存
文件页数/大小: 59 页 / 771 K
品牌: EXCELSEMI [ EXCEL SEMICONDUCTOR INC. ]
 浏览型号EX29DS160-90RTCI的Datasheet PDF文件第28页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第29页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第30页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第31页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第33页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第34页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第35页浏览型号EX29DS160-90RTCI的Datasheet PDF文件第36页  
E S I  
E S I  
ADVANCED INFORMATION  
Excel Semiconductor inc.  
toggles when the system reads at addresses within  
those sectors that have been selected for erasure.  
(The system may use either OE# or CE# to control  
the read cycles.) But DQ2 cannot distinguish  
whether the sector is actively erasing or is erase-  
suspended. DQ6, by comparison, indicates  
whether the device is actively erasing, or is in Erase  
Suspend, but cannot distinguish which sectors are  
selected for erasure. Thus, both status bits are  
required for sector and mode information. Refer to  
Table 10 to compare outputs for DQ2 and DQ6. Fig.  
12 shows the toggle bit algorithm in flowchart form,  
and the section “DQ2: Toggle Bit II” explains the  
algorithm. See also the DQ6: Toggle Bit I subsec-  
tion. Fig. 25 shows the toggle bit timing diagram.  
Fig. 26 shows how differently DQ2 operates com-  
pared with DQ6.  
START  
Read DQ7-DQ0  
Read DQ7-DQ0  
No  
Toggle Bit  
= Toggle ?  
Yes  
DQ5 = 1 ?  
Yes  
No  
Read DQ7-DQ0  
Twice  
Reading Toggle Bits DQ6/DQ2  
No  
Toggle Bit  
= Toggle ?  
Refer to Fig. 12 for the following discussion. When-  
ever the system initially begins reading toggle bit  
status, it must read DQ7-DQ0 at least twice in a row  
to determine whether a toggle bit is toggling. Typi-  
cally, the system would note and store the value of  
the toggle bit after the first read. After the second  
read, the system would compare the new value of  
the toggle bit with the first. If the toggle bit is not  
toggling, the device has completed the program or  
erase operation. The system can read array data  
on DQ7-DQ0 on the following read cycle. However,  
if after the initial two read cycles, the system deter-  
mines that the toggle bit is still toggling, the system  
also should note whether the value of DQ5 is high  
(see the section on DQ5). If it is, the system should  
then determine again whether the toggle bit is tog-  
gling, since the toggle bit may have stopped tog-  
gling just as DQ5 went high. If the toggle bit is no  
longer toggling, the device has successfully com-  
pleted the program or erase operation. If it is still  
toggling, the device did not completed the operation  
successfully, and the system must write the reset  
command to return to reading array data. The  
remaining scenario is that the system initially deter-  
mines that the toggle bit is toggling and DQ5 has  
not gone high. The system may continue to monitor  
the toggle bit and DQ5 through successive read  
cycles, determining the status as described in the  
previous paragraph. Alternatively, it may choose to  
perform other system tasks. In this case, this sys-  
tem must start at the beginning of the algorithm  
when it returns to determine the status of the opera-  
tion (top of Fig. 12).  
Yes  
Program/Erase  
Operation  
Complete  
Program/Erase  
Operation Not  
Complete, Write  
Reset Command  
Note:  
The system should recheck the toggle bit even if DQ5 = “1”  
because the toggle bit may stop toggling as DQ5 changes to “1”.  
See the subsections on DQ6 and DQ2 for more information.  
Figure 12. Toggle Bit Algorithm  
32  
Rev. 0E May 25, 2006  
ES29DL320  
 复制成功!