欢迎访问ic37.com |
会员登录 免费注册
发布采购

19-223/R6BHC-C03/2T 参数 Datasheet PDF下载

19-223/R6BHC-C03/2T图片预览
型号: 19-223/R6BHC-C03/2T
PDF下载: 下载PDF文件 查看货源
内容描述: [Dual Color LED,]
分类和应用: 光电
文件页数/大小: 10 页 / 286 K
品牌: EVERLIGHT [ EVERLIGHT ELECTRONICS CO., LTD ]
 浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第2页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第3页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第4页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第5页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第6页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第7页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第8页浏览型号19-223/R6BHC-C03/2T的Datasheet PDF文件第10页  
DATASHEET  
SMD . B  
19-223/R6BHC-C03/2T  
Precautions For Use  
1. Over-current-proof  
Customer must apply resistors for protection, otherwise slight voltage shift will cause big  
current change ( Burn out will happen ).  
2. Storage  
2.1 Do not open moisture proof bag before the products are ready to use.  
2.2 Before opening the package: The LEDs should be kept at 30or less and 90%RH or less.  
2.3 After opening the package: The LED's floor life is 1 year under 30or less and 60% RH or less.  
If unused LEDs remain, it should be stored in moisture proof packages.  
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the  
storage time, baking treatment should be performed using the following conditions.  
Baking treatment : 60±5for 24 hours.  
3. Soldering Condition  
3.1 Pb-free solder temperature profile  
260°C M ax.  
Above255°C  
10sec. M ax.  
30sec.M ax.  
3°C/sec.M ax.  
6°C/sec.M ax.  
Above 217°C  
60~150sec.  
Pre-heating  
150~200°C  
60~120sec.  
3.2 Reflow soldering should not be done more than two times.  
3.3 When soldering, do not put stress on the LEDs during heating.  
3.4 After soldering, do not warp the circuit board.  
4.Soldering Iron  
Each terminal is to go to the tip of soldering iron temperature less than 350for 3 seconds within once in less than the  
soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because  
the damage of the product is often started at the time of the hand solder.  
5.Repairing  
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering  
iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will  
not be damaged by repairing.  
9
RCopyright © 2010, Everlight All Rights Reserved. Release Date : 09-Dec-2013. Issue No: DSE-0010210  
www.everlight.com  
Rev.2  
LifecyclePhase: Expired Period: Forever